Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly, 50-Pin D-Type, Female to Female, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-FF-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Ferrules, 2m, 45º
A1604F5-F-0A200
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
20-Pin GMCT Male Connector, 10A, With Backshell
40-960-020-10A-M
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Also included is the backshell with screwlocks and cable clamp.
-
product
96-Pin SCSI Micro-D Discrete Wire
40-962-096-F
This connector is designed to allow users to terminate discrete wires with IDC connections to the 96-Pin SCSI Style Micro-D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
RTD Measurement for VMEbus
VME390
The VME390 features 24 two, three or four wire high-accuracy PT100 measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued.
-
product
Cable Assy 78-Pin D-Type Female to 16 x Mini Thermocouple Plugs, 1m
A078DFR-16M002T5A100
This 78-pin D-type thermocouple cable assembly is terminated with 16 male mini thermocouple plugs. It is constructed from 7/0.15 (26AWG) silver plated copper wire and screwlocks are provided to secure the D-type to its associated products.
-
product
10 Micron Wire Grid Polarizer
Fabricated from 10 micron diameter tungsten wire, and with a choice of wire spacing starting from 25 microns, these wire grid polarizers are suitable for use from approximately 100 microns (or 3 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-037-2m-MU
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Position Sensors & Encoders
Sensata's position line from Kavlico, BEI Sensors and Newall, make up our highly-engineered devices that span the entire range of position sensors, linear and rotary encoders, potentiometers, draw wires and inclinometers. They’re designed to deliver:
-
product
Power Quality Analyzer
PQM-703
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
product
20-Pin Scorpion Cable Assembly, Male to Female, 20A, 2m
A020AMR-020AFR-2A200
This is a 2m long male to female 20-Pin Scorpion cable assembly constructed from 19/0.41 (14AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
High Voltage (Hipot) Cable Tester
CH2
The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.
-
product
Cable Assembly, 78-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-078-0.5m-MU
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
MPO-MTP Polarity Instrument
JW8204
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8204 polarity instrument is an intelligent product,which is designed for polarity judgment and on-off analysis in MPO/MTP cable production. Through the one-button automatically scanning operation, the state of cable on and off, polarity (wire sequence) state, alarm and error analysis can be quickly indicated. JW8204 provides a fast, accurate and highly efficient solution for MPO/MTP cable production, inspection of semi-finished product and finished product.
-
product
Digital Transmission
The physical transfer of data (a digital bit stream or a digitized analog signal[1]) over a point-to-point or point-to-multipoint communication channel. Examples of such channels are copper wires, optical fibers, wireless communication channels, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared signal.
-
product
Voltage Testers
Shenzhen Everbest Machinery Industry Co.,Ltd.
Non-contact detection of 50 to 1000V ACRugged and double molded caseSuitable for outlets or against wire insulation testingFlashing red LED light indicatorBuilt-in bright flashlight with on/off buttonConvenient size with pocket clipAuto power offSystem self testUse on 50/60Hz circuitsComplete with two AA batteriesCATIII 1000VDimensions: 158 x 21mmWeight: 48g
-
product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m, HV
A009DM5-C-HA050
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
AC/DC Voltage Detector (CONTACT TYPE)
LVD-20
Standard Electric Works Co., Ltd
● Contact type.● LED indication and audible alarm sound when voltage is present.● Designed for AC/DC voltage detection. ● Used for bare wires or conductors.● Self-test function.● For indoor use only.● Low power consumption.● Light weight and compact.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A037DM5-T-0A100
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Cut Ends, 0.5m, 45º
A1604F5-C-0A050
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
product
Automatic Fiber Jacket Stripping Machine - FBT-3000
Shanghai Fibretool Technology Co.,Ltd.
The FBT-3000 automatic fiber peeling machine is a new type of optical cable end processing equipment, which is based on the eagerness of optical fiber connector manufacturers to improve production efficiency and reduce the skilled manual emergence of optical cable end processing equipment. In order to solve the problem that the skin layer of optical fiber is usually peeled manually with wire peeling pliers, and the artificial denudation is low in precision, low in working efficiency and low in product quality.
-
product
Cable Assy 37-Pin D-Type M/M 0.5m HV
40-970-037-0.5m-MM-HV
The 37-Pin D-Type High Voltage cable assembly is constructed from PTFE insulated 7/0.2 (24AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 37-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Cable Assy 78-Pin D-Type F/F 1m
40-970-078-1m-FF
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
product
Gauge Type T Thermocouple Wire
W-TW-40P2
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Test Programming
TestAssistant II
From a front-end graphical user interface to a back-end relational database, TestAssistant II organizes and maintains everything necessary for testing. Tester interfaces, wires, connectors, adapter cables, and other complex sub-assemblies are graphically represented.
-
product
20-Pin GMCT Female Connector, 10A, With Backshell
40-960-020-10A-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. Also included is the backshell with screwlocks and cable clamp.
-
product
Wireless Precision RTD Based Temperature Data Logger with LCD
RFRTDTemp2000A
The RFRTDTemp2000A is an RTD-based, wireless temperature data logger with display. This data logger is ideal for applications that require high accuracy temperature monitoring such as within laboratories, pharmaceutical and biotech industries. The RFRTDTemp2000A accepts 2, 3 or 4 wire 100Ω platinum RTD’s and features a device accuracy of +/-0.5°C.
-
product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 2m, HV
40-972-009-2m-FU-HV
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Solid State Active Synchro Control Differential Transmitter
Computer Conversions Corporation
The input is transformer isolated and accuracy applies over the operating temperature range and with +/-10% input amplitude and frequency variations. The operational amplifier outputs are not transformer isolated, and can be driven into external power amplifiers and Scott "T" transformers for 3 wire synchro outputs. A typical application of this series is in a conventional positioning servo system as a complex error processor. The use of the solid state CDX makes possible the design of servo systems that can be digitally programmed by direct computer input to the digital input of the SCDX.
