Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
product
Mobile sound Level Meter
SoundMeter
SoundMeter turns your iOS device into a handheld sound level meter (SLM) with support for exponential-time-weighted sound level (Lp) and equivalent sound level (Leq) measurements with various time and frequency weightings. The built-in signal generator tool can be used for generating calibration test tones, noise, chirps, or other periodic signals. SoundMeter also offers additional tools via in-app purchase, including a Noise Dosimeter and a whole or 1/3-octave real-time analyzer.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
Tone Generator
140BMC/6P
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
product
Cable Tester
CT100
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
product
Continuity Testers
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
product
MultiTracker
PK-108/108A
The Multitracker provides the most powerful combination of a high power Net toner, cable and network testers in one unit. It generates 2 selectable net tones with the capability to quickly locate and identify active network cables connected at HUB, Switch or Router, and live phone line systems. It also features a pin-by-pin cable testing with an auto scan and step modes for checking detail VDV (voice, data and video) cables pin-out configuration. Network test includes detecting PoE, Ethernet and Telephone services.
-
product
Cable Fault Locator
TX2002
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
Test DVD For OmniMic Precision Measurement Systems
OMDVD Version 1
The Dayton Audio OMDVD Test DVD brings the ease of the OmniMic V2 system to measurements of 5.1-channel audio systems. It’s the essential tool for professional installers and home theater enthusiasts to ensure proper audio calibration and optimization of a home theater or multichannel music system for the highest possible performance. The full functionality of the OmniMic V2 measurement system is now available through every channel of a 5.1-channel audio system thanks to the OMDVD Test DVD’s suite of high-quality test tones, and an intuitive menu structure that has been optimized for ease of use.
-
product
Tone Test Set
240 Weathertite
The AINES Model 240 Tone Test Set is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
product
Telephone Line Simulator
TLS-5
The TLS-5 Telephone Line Simulator offers the most convenient way to demonstrate or test telecom equipment where central office lines are not easily available. The TLS-5 functions as a virtual CO switch, providing four simulated central office lines with two talk paths, plus an audio interface port. Features include: 4 loop start lines, 2 talk paths, PBX features, programmable parameters, precise call progress tones, caller ID features, CLASS features, and programmable dial tones.
-
product
Spectrum Analyzer
Spectrum Analyzer for iOS is a powerful real-time audio analysis app. Designed with musicians and recording engineers in mind, it can also be used by anyone interested in the world of sound. Ideal for room tuning or speaker tuning, the app enables portable, precision audio measurement and visualization. The videos below demonstrate three of the included modules - Octave RTA, FFT Plot, and Spectrograph. A Test Tone Generator is also available.
-
product
LanCaster
4402700
Indicates all common wiring faults including split pairs Shows which end the installed link contains the fault Cable Length Meter, Tone Generator & Service Indicator Instant digital display gives unambiguous fault indication Rugged Palm-Top design weighs less than 350g (12oz) Complete with 1 Active Remote unit and test leads Up to 16 unique Active Remote units / Office Identifiers
-
product
PC based USB Real Time Analyzer
1) Measurement microphone and its accessories (a windshield and a microphone clip)2) XLR-to-USB Converter3) USB cable (1.5 m) 4) CD (contains the copy-protected Multi-Instrument Software) 5) USB hardkey (contains a Multi-Instrument Standard License)6) Audio Test CD (contains a list of audio test tones and noises) (AudioTestCD.zip or AudioTestCD.rar)7) 1/8” TRS cable (1.8m) 8) Black Soft Pouch Case 9) Individual Sound Level Calibration Data 10) Individual Microphone Calibration Data (only provided in RTA-168B)11) A small microphone stand
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
Cable Fault Locator
TX4000
Auto Fault Location Rugged Palm-Top design Weighs less than 350g (12oz) 11 Measurement Ranges up to 4000m 25, 50, 75 & 100ohm Selectable Cable Impedance User Variable Gain Control Built in Tone Generator for Pair Tracing and Identification Suitable for testing all Communication and Power Cables Environmental Protection IP54 CE Approved Soft bag & Test Leads
-
product
Multi-Tone Test Systems
AR RF/Microwave Instrumentation
AR’s state-of-the-art multi-tone systems are designed to test RF Radiated and Conducted Immunity faster than ever before. Both the MT2IEC10V3M and MT4IEC10V3M fully comply with IEC 61000-4-3:2020 Edition 4, allowing for multiple tone testing, reducing test time by up to 74%. Commercial, aviation, and automotive industries, will perform RF radiated and conducted immunity testing faster, more accurately, more efficiently, and more closely to a real-world environment.
-
product
LanSeeker Cable Tester
#TP500C
The LanSeeker is a fast, rugged cable tester and tone generator in one unit. It displays cable test results using LED indicators on the main and remote unit. An easy-to-use professional grade tool, the LanSeeker is a must have for residential and commercial cable installers. When the unit senses a connection between the main and […]
-
product
Cable Tester/Tracer/Toner, 3-In-1 Professional, Pocket
TCT-700
A mult-function test set for RJ-45 LAN cable, BNC and "F" coaxial cable, tone generator, continuity and 6P2C/4P2C jacks. Ideal for electricians, service technicians. telecommunications, networking or general home use.
-
product
Test Set
TS® 25D
This feature-rich test set is a necessity for a variety of installs. The TS25D Test Set features data lockout and lockout override, making you completely safe in talk or monitor mode. The DSL/POTS filtering technology allows you to safely draw dial tone without downing DSL.
-
product
Command Encoder/Exciter
Kratos Defense & Security Solutions, Inc.
The Command Encoder/Exciter (CEE) is a rack-mount unit ideal for test and verification of Flight Termination Receivers (FTR) and/or Tone Receiver/Decoders. It accepts a universal AC power input, and it generates a modulated RF output carrier signal adjustable in 100kHz steps from 406MHz – 450MHz from suitable for interrogation all RCC 319 compliant IRIG FTRs.
-
product
LCD Multifunction Cable Tester
MT-7059
Display test result on large LCD for easy reading and cable status identificationThe wire can be tracked directly in connection with Ethernet service, router, and PC terminalValidate and troubleshoot wiring on RJ11/RJ45 cables, Coaxial cable, USB cable, IEEE 1394 cableTest cable status for continuity, shorts, opens,miswired, crossover9 different tones selection for convenience use under different environment conditionAll installation and maintenance fields of telecommunication, networking, cable TV and more
-
product
LAN Tester
RJ45
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
product
Audio Test Tone Generator
Tone Plug
The TONE PLUG offers five user selectable sine wave test tones at frequencies of 100, 250, 400, 1K and 10KHz. An additional 5 special function test signals are also provided.
-
product
Cable Fault Locator
TX2001
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
Network Analyzers
The LanExpert LE80 Inline network analyzer is a single solution for analyzing and troubleshooting networks from the cabling to the packet. The LE80 tests Wiremap, Length, PoE, Tone and Port ID.
-
product
Mouth Simulator
BO1032
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
-
product
Telephone Wire Cable Tester For Testing Continuity With Sender And Receiver
PHCT55
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.
-
product
NTSC PATTERN GENERATOR
PG-28
Model PG-28 NTSC Pattern Generator can be use to quickly and easily troubleshoot, test, and align NTSC television. Features a wide selection of popular video patterns including Color Bars, Crosshatch, Dot, Staircase, Circle, Center Cross, Window, and Raster for accurate and comprehensive TV troubleshooting and testing. Supports both progressive and interlace scanning system. Composite video and S-Video output. 1KHz audio tone for audio troubleshooting.
