Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m
A015DF4-T-0A050
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
PXI Strain Gauge Simulator Module 6-Channel, 2k
40-265-306
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Dial Strain Gauge
DRK8093
Shandong Drick Instruments Co., Ltd.
This stress (birefringence) sources are due to uneven cooling or external causes such as mechanical action, which directly affect the optical glass, glass products, quality transparent plastic products. Therefore, stress control is optical glass, glass products, plastic products, such as transparency in the production process extremely important part. The strain gauge can be qualitatively or quantitatively by observing stress to identify products (DUT) quality, are widely used in optical glass, glass, transparent plastics industry for fast, a lot of testing. In fact, it can not be solved by math the complex problems.
-
product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
product
Test Equipment
Southern Photonics designed and manufactured all the test equipment currently being manufactured by Coherent Solutions, as well as equipment for non-telecoms applications. This includes FBG strain interrogators, optical pulse phase analysers, OSNR meters, optical power meters, optical spectrum analysers, optical gas sensors… you get the idea. All test equipment we build is robust and easy to use. The picture shows some of what we can do – anything from prototype benchtop test gear (as in the combination ASE source and laser combiner on top of the stack) to field test equipment (the portable fast OSA on the bottom).
-
product
Bending Deflectometers For ISO 178, JIS K 7171, And ASTM D790 Compliant Testing
After tensile testing, flexural tests are the most common strength tests for plastics and other resins. The main standards for plastic flexural (bend) tests are ISO 178, JIS K 7171, and ASTM D790, which require very accurate test systems. These standards include flexural strain measurements using a deflectometer, ranging from micro-strain measurements in the elastic region, the reversible elongation at the beginning of tests, to larger strain measurements in the plastic region. Shimadzu's deflectometers integrate easily into AG-X plus series, AGS-X series, and EZ-X test frames and Trapezium X testing software. Since these deflectometers push up against the specimen from below, the specimen color is not a limiting factor, as can be for laser type non-contact deflectometers. Furthermore, these deflectometers can partially absorb the shock during specimen failure, preventing specimen fragments from scattering.
-
-
product
Contactless Laser Extensometers
Jinan Testing Equipment IE Corporation
Model LE-05 and LE-15 extensometers measure strain optically, without contacting the specimen, using laser diode technology. The extensometers are self-contained and portable. They may be interfaced with a variety of testing machines and data acquisition systems using the ±10V analog output or bi-directional RS-232 serial port. Operation may be local or remote. A digital display is included. The scanning beam is always perpendicular to the specimen, unlike most laser extensometers. This eliminates errors when viewing through windows in chambers. It also minimizes sensitivity to the distance between the extensometer and the sample. Because the unit measures reflected light, no receiver is required behind the sample.
-
product
Measurement System
2800
The 2800 Chromatic Dispersion Measurement System provides fast, accurate measurements of chromatic dispersion and length of all types of single-mode optical fibers. Easy to use Windows-based software provides all industry standard calculation techniques for the determination of zero dispersion wavelength and dispersion slope. Options are available for the measurement of Polarization Mode Dispersion (PMD) and Fiber Strain.
-
product
Benchtop X-ray diffraction (XRD) instrument
MiniFlex
New sixth generation MiniFlex X-ray diffractometer (XRD) is a multipurpose analytical instrument that can determine: phase identification and quantification, percent (%) crystallinity, crystallite size and strain, lattice parameter refinement, Rietveld refinement, and molecular structure. It is widely used in research, especially in material science and chemistry, as well as in industry for research and quality control. It is the newest addition to MiniFlex series of benchtop X-ray diffraction analyzers from Rigaku, which began with the introduction of the original MiniFlex system decades ago.
-
product
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth
410112712
Enclosure, S6, 2U Height, 4 Cable Clamps, 12" Depth Includes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With the cable clamps open- stiffener bar can be removed allowing installation or removal of cables without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
product
Hand Dynamometer Logger Sensor
NUL-237
This sensor comes with a hand held unit with a built in strain gauge. The sensor measures the pressing force on the hand held unit.
-
product
Rectal Probe For Rats (Isolated)
RET-2 ISO
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - '' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds.
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 350 Ohm
50-265-014
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
S-Type Load Cells
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
Chuan Sheng Electronics Co., Ltd.
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
product
Strain Gauge for Measuring and Testing
Zhonghang Electronic Measuring Instruments Co. Ltd.
Zemic Strain Gauge for Measuring and Testing
-
product
20-Pin GMCT Cable, Male to Unterminated, Ferrules, 10A, 2m
A020GMR-F-0C200
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
3-Hole Bolt On Strain Gauge Sensor
The series 460 3-hole bolt-on strain sensor has a unique design, eliminating the temperature effect on bending and strain of the application, and. can work in almost any environment and in any weather.Datum Electronics offers two types of multi-element bolt-on strain sensor that have been developed to provide a rugged and robust production sensor with the benefits associated with a complex strain gauge installation. The bolt-on strain sensors have been designed to measure tensile and compressive bending stresses ranging from 50 to 1100 micro-strain, for use in applications including vehicles, civil engineering structures, silos, hoppers, vessels, and specialist engineering projects.
-
product
Multi-Axis Hot Deformation System
MAXStrain
The system restrains specimens lengthwise while allowing unlimited deformation in the other two dimensions. As a result, very high strain levels can be introduced into specimens to produce a sample of ultrafine-grain or nanoscale material that is large enough for subsequent properties testing.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
68-Pin SCSI Micro-D M to 2x34 2m
40-971-068-2m-MF
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
product
Flush Diaphragm Pressure Sensors
Honeywell Industrial Automation
For high-frequency pressure measurements or in applications with severe space limitations, Honeywell Sensotec offers subminiature flush diaphragm pressure sensors in ranges from 0100 psi to 020,000 psi (010 to 01,400 bar). All-welded, machined stainless steel sensing diaphragms ensure ruggedness. Bonded piezoresistive and metal foil strain gauges offer high reliability. Millivolt and optional high-level outputs are compatible with most data acquisition systems.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
Optical Distributed Sensor Interrogator
ODiSI 6000 Series
The ODiSI 6000 Series is a powerful measurement system specifically designed to address the modern test challenges of advanced materials and systems. The ODiSI system delivers the highest definition distributed sensing of strain and temperature available, giving you maximum insight and visibility into your component or process.
-
product
High-Speed Digital Image Correlation System
Q-450
The 3D High-Speed Image Correlation System Q-450 allows the full-field, non-contact and three-dimensional dynamic measurement of shape, displacements and strains on components and structures made from almost any material. Based on the digital image correlation technique, the Q-450 system is designed for full-field vibration analysis and high speed transient events. This makes it ideal for ballistics testing, fracture mechanics, shock excitations, the Hopkinson Bar test, or Impact Testing.
-
product
Contactless Video Extensometers
Jinan Testing Equipment IE Corporation
Deformation measurement of samples during material testing with use of the Video extensometer MercuryRT allows applying multiple virtual probes (Movement Sensors)on markers and advanced image featuresto be tracked, including the natural pattern of the sample surfaces.The common resolution of standard system is within 500 nm and 5 m. The system fulfils class 0.5 or B-1 of classification according to ISO 9513 and ASTM E83. In certain camera use case, the system resolution reaches the level of 100 nm - 500 nm and system fulfils the class 0.2. The strain resolution can reach 10 microstrains. Material testing,Component testing ,FEA validation,Vibrography .
-
product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 3m
A020GFR-C-0C300
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
3D And 2D Visualization Software
3DViz
The 3DViz software provides intuitive 2D and 3D visualization of high-definition sensor data. Software allows strain or temperature data from an ODiSI system to be visualized directly on a 3D CAD model or a 2D image.
-
product
Inspection Systems
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
-
product
Band-On Telemetry System
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
