Filter Results By:
Products
Applications
Manufacturers
Shock
A shock test transmits kinetic or thermal energy into a UUT in a relatively short interval in a controlled enviroment.
See Also: Thermal Shock, Vibration
- Virginia Panel Corporation
product
Replacement Protective Cover, G2, ITA
410112680
The ITA Protective cover is made of vinyl thereby making it more durable and shock resistant to protect your contacts and modules in case of harsh impact.
-
product
2 Zone Thermal Shock Test Chamber
2-Zone Thermal Shock Testing Equipment with programmable electronics.
-
product
Industrial Shock Absorbers
ACE industrial shock absorbers work hard. Their application means moving loads are evenly decelerated over the full stroke. The result: the lowest braking force and shortest braking time. The MAGNUM series from ACE is viewed as the reference standard for medium-sized damping technology.
-
product
HV Rotary Switches
B-1003
A key feature of our rotary switches is their simple mechanical design which results in conservative stress levels for trouble-free, long life use. In addition, each rotary switch has a reinforced chassis design utilizing G-10 or G-11 fire retardant anti-tracking coated epoxy glass insulation. G-7 silicone glass is used for special applications where RF or high temperatures are involved. Heavy duty contacts, specifically designed to minimize corona in the Ross rotaries, are made of highly conductive yet weld resistant alloy with high contact closing force. This high force gives our rotary switches high momentary current capability and a reputation for their ability to withstand high shock and vibration as well as other severe environmental conditions. Ratings to 150kV, to 200A. When immersed in insulating oil, fluid or gas, the voltage withstand value is at least doubled and the interrupt capability is much greater. In a gas atmosphere, no modification is required. However, immersion in oil or fluid may require modification in some cases, at an extra cost (optional). Each unit is either manually or electrically operated. One SPDT contact is standard on most units. The auxiliary contact is used as an interlock for protection against "Switching Hot".
-
product
Hardware-Software System
Shock Impact Recorder
This system is complex of recording instruments intended for measurement and recording of shock impact parameters produced by shock testing machines.
-
product
Bending Deflectometers For ISO 178, JIS K 7171, And ASTM D790 Compliant Testing
After tensile testing, flexural tests are the most common strength tests for plastics and other resins. The main standards for plastic flexural (bend) tests are ISO 178, JIS K 7171, and ASTM D790, which require very accurate test systems. These standards include flexural strain measurements using a deflectometer, ranging from micro-strain measurements in the elastic region, the reversible elongation at the beginning of tests, to larger strain measurements in the plastic region. Shimadzu's deflectometers integrate easily into AG-X plus series, AGS-X series, and EZ-X test frames and Trapezium X testing software. Since these deflectometers push up against the specimen from below, the specimen color is not a limiting factor, as can be for laser type non-contact deflectometers. Furthermore, these deflectometers can partially absorb the shock during specimen failure, preventing specimen fragments from scattering.
-
product
AGS Energy Source
Teledyne Marine AG Geophysical Products
Source firing systems for sealed electrical interconnect where high shock and mechanical survivability is paramount.
-
product
Heat Test Probe 43
CX-43
Shenzhen Chuangxin Instruments Co., Ltd.
It's the necessary tool to proceed protecting electric shock test of household and similar electrical appliances.
-
product
Handheld Water Quality Meters
LAQUA PH210
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
product
Super Energizer 5
SE-5
Parker McCrory Manufacturing Co.
A powerful model designed for today`s large pastures. Ideal for single or multi-wired high tensile fences. The Super Energizer 5 does everything a fence controller should do – it just does it better!!! Super Energizer 5 is equipped with a built-in DIGITAL performance meter which tells you the exact condition of fence. Shocks through wet weeds and brush. Over 8,000 volts of holding power with 500 OHM load. New color coded fence and ground terminals. Red to the fence and Black to ground. The Super Energizer 5 controls both predators and livestock, including sheep and goats. Fuse protection with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
Open Path Combustible Gas Detector
SafEye (Quasar 900)
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
product
Environmental Testing
DATASYST Engineering & Testing Services, Inc.
Simulate real-world environmental conditions to know how your product or component measures up. DATASYST evaluates how your product responds to environmental stressors, including temperature, thermal shock, humidity and altitude.
-
product
VCOs with Single Output
Analog Devices voltage controlled oscillator (VCO) portfolio supports a broad range of applications. Our extensive product line includes multiple devices that offer excellent phase noise performance over temperature, shock, and process due to their monolithic structure. We also offer ultrasmall size, low phase noise, low power consumption, and wide tuning range options to meet multiple design needs.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InP1012-60
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Flip-chip packaging provides shock & vibration resistance• ENEPIG surface finish for solder bonding• Low loss package with organic overmold• Test board with K-connectors can be providedDC-60GHz40+ Gbps
-
product
Data Logger MSR165 for Shock and Vibration
MSR165
The robust MSR165 data logger is capable of making 1600 acceleration (shock, vibrations) measurements per second in all three axes. Shock monitoring is possible up to +/- 15g, 32 measurement values are recorded even before the event takes place.
-
product
Ground Earth Resistance Tester
2678X
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 TO-5
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
IEC60068-2-75 Ik08 Spring Impact Hammer
CX-IK08
Shenzhen Chuangxin Instruments Co., Ltd.
The spring Hammer consists of three principal parts: the body, the striking element and the release system. It's used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance with IEC/EN, UL/CSA and other international standards.
-
product
SparkFun Triple Axis Digital Accelerometer Breakout
ADXL313 (Qwiic)
The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI.
-
product
Coaxial Multi-Position Switches
Space-qualified multi-position switches are sometimes used during launch, which means that they need to be operational under very harsh conditions, such as continuous RF power during actuation (‘hot switching’), as well as high levels of shocks and vibrations. Dow-Key has proven designs on numerous programs such as ORION, VENICE, and AMOS.
-
product
Package Testing
AMERICAN TESTING LABORATORY tests all types of product packaging, from shipping crates to child resistant packaging. In addition, we test the effects of many types of physical and environmental shocks on products inside the packaging.
-
product
Transportation Environment Data Recorder
For investigation and evaluation of the transportation route by measuring vibration,temperature and humidity on the whole travel.For search of the cause of defects of any expensive freights as shock, fall, temperature or humidity,and location of place and time.For evaluation of vibration durability of the freights or R & D of the most suitable package using the function of tailoring.Specifications
-
product
Hybrid LX
HLX Series
*Surface Mount Package *Ruggedized, Hi-Rel *Hermetically-Sealed *Extreme Shock and Vibration Tolerance *Fast Switching Designs Available
-
product
Sources & Converters
High reliability, low-phase-noise, high-coherence, large operational temperature range, exceptionally low g-sensitivity for high vibration and shock performance.
-
product
Non-contact Io/Ior Leakage Clamp Meter
MCL-500IRV
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・True RMS measurement (I, Io, V).・With filter switch to cut high frequencies.
-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different accessories, the Spring Fatigue Testing Machine can test springs of different sizes. Adopting the single-chip machine control, the Spring Fatigue Testing Machine realizes auto stop function when it reaches the preset test times. The Spring Fatigue Testing System is widely used in quality controls for spring, shock absorber production, and relevant applications.
-
product
Thermal Shock Chambers
VTS-Series
Vertical Thermal Shock chambers consist of two separately controlled hot and cold zones. Product is transferred between these zones for rapid product temperature changes. Thermal Shock Chambers are designed to perform tailored environmental stress screening of component and board level electronic assemblies. The return on investment in both actual savings and customer confidence adds greatly to the value of electronic assemblies screened in a CSZ thermal shock system.
-
product
Board-to-FPC Connector for 5G Millimeter-Wave Antenna Modules
Panasonic Industrial Devices Sales Company of America
Panasonic's Board-To-FPC Connector for 5G Millimeter-Wave Antenna Modules offer good SI/EMI/EMS characteristics for high-frequency applications and features our industry-leading Tough Contact construction that achieves high contact reliability and retention force. Tough against shock impact by misalignment, the fully-shielded structure in both socket and header significantly improves EMI characteristics necessary for RF applications such as 5G.
-
product
RMC-8355, 2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI
782568-01
2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI - The RMC‑8355 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon E5620 quad‐core processors that support up to 96 GB of DDR3 RDIMM ECC RAM. The RMC‑8355 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8355 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
product
Transient Recording Systems
5800 Series
Series 5800 is a transient recording system for explosive and other high speed recording applications like shock & vibration testing. Each measurement channel includes high bandwidth signal conditioning, digitizing rates up to 10MS/s and recording to onboard memory. Series 5800 can be used in laboratory or harsh physical environments and includes turnkey application software. A system consists of an Enclosure, I/O Module and Software.
-
product
High-Speed Digital Image Correlation System
Q-450
The 3D High-Speed Image Correlation System Q-450 allows the full-field, non-contact and three-dimensional dynamic measurement of shape, displacements and strains on components and structures made from almost any material. Based on the digital image correlation technique, the Q-450 system is designed for full-field vibration analysis and high speed transient events. This makes it ideal for ballistics testing, fracture mechanics, shock excitations, the Hopkinson Bar test, or Impact Testing.
