Filter Results By:
Products
Applications
Manufacturers
SPI
assures volume and area of paste application.
-
product
Firmware for High-speed HDLC Mode
OP-FW10G
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
-
product
COM Express Type 7
ROM-8720
Advantech ROM-8720 COM Express Type 7 Compact Computer-on-Module is powered by NXP LS1046A SoC which includes four Arm Cortex-A72 cores for Edge networking and Edge firewall, two 10Gbsp-KR and up to four Gbps for the networking communications. Three PCIe, three USB 3.2 Gen1 and three USB2.0 for the embedded interface expansions. two UART, one SPI and 8 GPIO for embedded device controls.
-
product
Low-power, High-performance FPGA
iCE40 LP/HX
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
product
Board
Arduino MKR ZERO (I2S bus & SD for sound, music & digital audio data)
MKR ZERO has an on-board SD connector with dedicated SPI interfaces (SPI1) that allows you to play with MUSIC files with no extra hardware!
-
product
Multi Protocol Analyzer
LE-3500R
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, SPI, I2C, 2 LANs And DIO (2-in/1-out)
IFB125
The IFB125 is powered by the low-power Freescale i.MX6UL processor in the ARM® Cortex™-A7 micro architecture. It supports extended operating temperature ranging from -40°C to 70°C, and can withstand vibration up to 5G. Its flexible wide voltage range 9V - 48V DC power input with a lockable terminal block type connector also enhances its reliability in harsh environments. To meet most of Industrial IoT needs, the IFB125 supports multiple communication interfaces for maximum flexibility, including LAN, serial, USB, and digital I/O ports. The Industrial IoT gateway has 256MB onboard memory that features data transfer rates of DDR3-1600, as well as 4GB eMMC flash memory onboard for storage. This embedded IoT gateway platform is equipped with one PCI Express Mini Card slot and one SIM card slot. Additionally, it supports DB9 connectors with both SPI and I2C function as communication protocols to suit for specific applications
-
product
LoRa 1W Breakout
915M30S
Do you need power? This breakout for the 915M30S module from EBYTE is a 1W (30dBm) LoRa transceiver. LoRa is great for long range (miles), low power (in sleep), and low data rates (~500bps). This breakout board is designed to connect to any platform that has SPI and 6 available GPIO. We include a robust edge mount RP-SMA connector to connect large LoRa (915MHz) antennas. In addition, the on-board U.FL connector can be used if you need to get outside a metal enclosure.
-
product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
product
SparkFun Triple Axis Digital Accelerometer Breakout
ADXL313 (Qwiic)
The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI.
-
product
Channelized Up-Converter
UPCV Series 5” x 2.5” x 0.6”
*Connectorized Package *Wide Choice of Frequency Ranges *IF to Ka-Band Solutions Available *Integrated Filters *Gain Control *USA, RS232 or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Module Spectrum
nRF52833 Series
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
product
4 Channel ADC FMC Module
ADCFN04 – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
ARINC 429 Card
SET-1623
The SET 1623 ARINC Card has 32 Tx/Rx Channels. These 32 Tx/Rx channels are structured in 4 banks (P0.x to P3.x) 8 channels each. Each bank is controlled by a dedicated SPI (SPI0 to SPI3) located on RTI.
-
product
USB Logic Analyzer- High Speed Data Logger -SPI / IC Analyzer
LOG Storm
Logic analyzers are key tools for that process – they offer visibility over what happens in your digital electronic system.
-
product
Beagle I2C/SPI Protocol Analyzer
TP320121
The versatile Beagle™ I2C/SPI Protocol Analyzer is the ideal tool for the embedded engineer who is developing an I2C, SPI, or MDIO based product. The Beagle analyzer provides a high performance bus monitoring solution in a small, portable package. Perfect for engineers in the field and in the lab.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
SparkFun Micro OLED Breakout
The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s "micro", but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of all, though, is the Micro OLED is easy to control over either an SPI or I2C interface.
-
product
Open Standard Module (OSM)
ROM-2860
Advantech ROM-2860 OSM 1.1 Computer-on-Module is powered by Qualcomm QCS6490/5430 SoC which includes up to Arm v8 Cortex® in combination with Andreo GPU 643 and Andreo VPU 633 graphics engine. It provides PCIe, USB 3.2, Giga Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and eDP, DP, MIPI-DSI display for embedded applications.
-
product
Environment click
Environment click measures temperature, relative humidity, pressure and VOC (Volatile Organic compounds gases). The click carries the BME680 environmental sensor from Bosch. Environment click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI or I2C interface.
-
product
AOI & SPI Test Systems
Xceed AOI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The Xceed enables true 3D measurement and provides the most accurate and repeatable inspection results with the minimum false calls. It’s designed with Advanced Signal Processing which gives results in noise-less, clear, and accurate 3D images.
-
product
Micsig Smart Oscilloscope
STO1000C/E
Shenzhen Micsig Instruments Co., Ltd.
*Up to 70Mpts memory depth, Zoom into a selected part of the captured waveforms to get more details. *Support serial triggering and decode (I2C, SPI, RS232/UART,CAN, LIN) and Aerospace and defence (MIL-STD 1553, ARINC 429). Two formats to display decoding, text and graphic.
-
product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
product
Ultra-Low Power Computing Module
CM22303
LinkedHope Intelligent Technologies Co.,Ltd.
CM22303 uses Intel® 7th generation Kaby Lake-Y platform and Core M Ultra low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.6 GHz and the display output resolution can be up to 4K. CM22303 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. SPI BIOS is designed on board to support dual-channel low voltage on board memory (up to 16GB), Gigabit Ethernet, TPM module and other functions. With high-performance and low power consumption, it can be widely used in the field of low power embedded systems. Meanwhile, CM22303 adopts COM Express standard and is compatible with Type10 pin out definition, and also provides rich peripheral interfaces such as USB3.0/2.0, PCIe, SATA, HD Audio etc.
-
product
Embedded Analysis Software for the 2000 X-Series
D2000GENB
Test and debug I²C, SPI, RS232/422/485/UART designs with triggering, decoding, and pass / fail mask limit testing.
-
product
3D Solder Paste Inspection (SPI)
Systems designed for solder paste inspection (SPI) quickly and reliably check the solder paste deposits on the circuit board.
-
product
Multi Protocol Analyzer
LE-2500R
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
product
SparkFun MicroMod GNSS Carrier Board (ZED-F9P)
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
