Filter Results By:
Products
Applications
Manufacturers
Resistance Temperature Detectors
- variable-resistance sensor measuring temperature by fluctuations in resistance.
- Pickering Interfaces Inc.
product
Resistance Temperature Detectors (RTD) Simulators
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
product
16 Thermocouples/RTD Ch
APCI-3200-16
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel16 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 8 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
product
sbRIO-9219, Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
781027-01
Non-Enclosed, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The sbRIO‑9219 is designed for multipurpose testing. With the sbRIO‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel. Non-enclosed modules are designed for OEM applications.
-
product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
Data Acquisition Recorders & Loggers
DAS1800
The DAS1800 can be configured for a wide variety of applications with slots for 10 input modules each supporting 4 or 8 measurement channels. Acquire data from any sensor with a voltage or current output (with shunt), or directly measure voltage, resistance, or temperature using thermocouples or resistance temperature detectors (RTDs).
-
product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
Ignition Pulse Detector
IP-292/296
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
product
4 Thermocouples/RTD Ch
APCI-3200-4
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel4 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 2 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
product
Process Indicators & Field Devices
Field devices from the Field Analog series record and convert signals from resistance temperature detectors, thermocouples, resistance-type sensors, and voltage sensors directly on site.
-
product
PXIe-2725, 8-Bit, 18-Channel PXI Programmable Resistor Module
781986-25
8-Bit, 18-Channel PXI Programmable Resistor Module - The PXIe‑2725 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXIe‑2725 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
C Series Universal Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Planar-Doped Barrier Diode Detector, 0.01 to 18 GHz
8474B
The Keysight 8474B is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474B is also very rugged with high resistance to ESD damage. The Keysight 8474B detectors are available with 0.01 to 18 GHz and a type-N connector. This detector offers options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of these devices is typically better than plus or minus 0.3 dB, no matched response option is offered.
-
product
Resistance Temperature Detectors
Sensors used to measure temperature by correlating the resistance of the RTD element with temperature.
-
product
sbRIO-9218, Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module
783362-02
Non-Enclosed, 24-Bit, 51.2 kS/s/channel, 2-Channel C Series Universal Analog Input Module - The sbRIO‑9218 helps you perform multipurpose testing. With the sbRIO‑9218, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors. You also can use the sbRIO‑9218 to perform quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. You can individually select and perform a different measurement type on each channel. Additionally, the sbRIO‑9218 features 60 VDC analog input isolation. Non-enclosed modules are designed for OEM applications.
-
product
Ground Fault Protection Monitors
The Earth Fault Resistance Monitor (EFREM) and the Rotor Health Monitor (RHM) provide wireless rotor ground fault and temperature monitoring for generators and motors. The systems replace older slip ring contact ground fault detectors on any synchronous generator or motor.
-
product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
785994-01
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 TO-5
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Temperature Measurement IR Sensors & Detectors
1SC Compensated
A thin film-based single channel thermopile detector that offers thermal compensation to minimize effects of sudden ambient temperature change during the initial five seconds of change. The 1SC Compensated comes in a TO-5 package with a medium sized 1.0 x 1.0mm active area. Compensation is achieved through the integration of two additional half-sized thermopile elements. Internal aperture is standard and precisely defines active area for applications with FOV and/or spot size requirements.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 TO-18
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a small TO-18 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
product
Temperature Stabilized Resistance Standards
Measurements International Ltd.
The temperature stabilized resistance standards offer customers the very best in accuracy, and stability. With 3 different models to choose from, covering the full range of resistance values.
-
product
Resistance
Ohmmeters, decade boxes and resistance standards for tests against safety and quality.
-
product
Detectors
Solar blind detector for operation in the 1 to 180 nanometer region. It is encased in a vacuum tight housing for vacuum operation. The Model 425 is ideal for measurements in the Extreme and Vacuum UV (EUV and VUV) where the solar blind feature eliminates potential interference from long wavelength ultraviolet and visible light. It may be operated in pulse-counting mode or DC. The CEM is also available with coatings like Cesium Iodide or Magnesium Fluoride to enhance response in different energy regions.
-
product
Radar Detectors
histler''s FDSR (Field Disturbance Sensor Rejection), the most recent advancement to combat new vehicles equipped with Frequency-Modulated Continuous Wave (FMCW) K band blind spot and collision avoidance devices that clutter nearly all of K band causing a normal radar detector to alert continuously.
-
product
Temperature Measurement IR Sensors & Detectors
M34
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
product
RF Detectors
BroadWave designs and manufactures RF Detectors and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
-
product
Metal Detectors
In our ever-changing landscape, important assets are buried or paved over making finding for them both difficult and time consuming. Valve and manhole covers are often lost after ground work activities, re-surfacing or after heavy snow falls. Buried boundary markers can also be difficult to find. Most of these items are manufactured using magnetic or ferrous materials. These can be detected using the VM-880. As it detects only ferrous materials, aluminum cans, bottle caps, etc. are rejected. The simple audio and visual user interface has been designed to minimize training requirements while the latest technologies are employed to ensure maximum sensitivity and depth range. Particular attention has been made to ensuring the weight of the VM-880 is minimized, at just 1.54lbs (0.7kg), it is by far the lightest in its class. This has been achieved without compromise to strength. The submersible carbon fiber antenna tube is both lightweight and provides maximum protection to sensitive sensors.
-
product
Automated Temperature Resistance Standard
Measurements International Ltd.
Exceptional Stability, Cost-effectiveness, Performance-based Results, 10 Ω, 25 Ω, 100 Ω, 200 Ω, 400 Ω and 1000 Ω Internal Standards, Built-in Temperature Chamber for Optimal Performance.
-
product
Phase Detectors
High DC output versus phaseLow DC offsetRugged metal coaxial packageTiny surface mount packages, 0.38 x 0.50 x .023 in.
