Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
product
Low-power, High-performance FPGA
iCE40 LP/HX
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
product
Cam Switches
Mechanical row-position counters with an exchange unit are available for standard applications and for applications with safety switching points. The whole ram unit can be removed using two bolts to replace the individual ram. This saves time and money if service is required because it is not necessary to remove the whole switch. The switches are recognizable by the blue-colored anodized ram plate
-
product
ARINC 429 Test And Simulation PXI Module
PXI-C429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Output Channels, PCI Express
APCIE-3121-16-8
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Low Cost Emulator
EB-ST62
# Supports Most of the ST62 Microcontrollers# Real-Time Emulation up to Device Frequency# 3.3V and 5V Operating Voltages# Real-Time Trace Buffer# Source-Level Debugger for C and Assembler# Unlimited Number of Breakpoints# Stack Overflow Debug Breakpoints# 8K Bytes Emulation ROM# 192 Bytes Emulation RAM# 128 Bytes Emulation EEPROM# On-Board Switches and LEDs
-
product
MIL-STD-1553 Eight-Channel VME Board
VME-8-1553
The V-Orchestra™ is an eight channel MIL-STD-1553B board which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 32K word of internal RAM.
-
product
RMC-8355, 2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI
782568-01
2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI - The RMC‑8355 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon E5620 quad‐core processors that support up to 96 GB of DDR3 RDIMM ECC RAM. The RMC‑8355 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8355 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
product
SMARC V2.0 SoM With I.MX8M Quad/Dual 1.5 GHz/1.3 GHz (Industrial) SoC, 4GB RAM, 64GB EMMC, CAN, MIPI CSI/DSI And HDMI 2.0
SCM180
The SCM180 is a SMARC v2.0 system on module with a choice of quad- or dual-core Arm® Cortex®-A53 processors. The ultra low power, high performance, RISC-based module measures only 82 x 50 mm and utilizes the powerful i.MX 8M processor. Its scalability, optimized pinout schematic and low profile design offers high level of versatility to help system integrators drive their important projects forward. The SCM180 is unique among other SMARC modules of its kind because it features Trusted Platform Module (TPM) for optimum security. With a discrete, dedicated microcontroller designed to support hardware encryption and decryption, the SCM180 delivers enhanced security for an added layer of protection. It also offers a choice of operating temperature ranges and can operate reliably in harsh environments. The SCM180 is suitable for a wide range of smart, portable/mobile-integrated IoT applications including robotics, automotive, factory automation, smart agriculture, casino gaming, medical, retail, surveillance and more. With its NXP artificial intelligence core technologies-enabled capabilities, the SMARC module can be programmed to support smart automation and machine-learning application requirements.
-
product
PCIe-Mini
PCIe-Mini-DA4
The PCIe-Mini-DA4 is a PCiexpress Mini board with a total of 4 voltage outputs D/A. Each output is followed by a buffer able to provide +/- 30 mA. Special function code allows global updates of all channels or by a group of eight channels at atime. Standard ping-pong output registers for each channel or optional data RAM allows waveform generation with minimum processor involvement.
-
product
Module Spectrum
nRF52833 Series
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
product
Low Latency DRAM
Low Latency DRAM is our newest large-density memory boasting high performance. Incorporating high-performance technology used in our synchronous SRAM and the pseudo-SRAM technology used in mobile-specified RAM, Low Latency DRAM is ideal for use in various networking applications. With a Fast random access time-and data latency lower than other DRAM products-Low Latency DRAM realizes extremely high performance compared to commodity DRAM.
-
product
Fiber Channel Simulyzer
Avionic Interface Fiber Channel SimulyzerTM products are multifunctional, high-performance Fiber Channel interface and test boards. The products have both a data generation / simulation function and a monitor / analysis function on one board. Avionic Interface Fiber Channel products can be used with the most popular upper layer protocols FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All FibreChannel products use multiple processors with large onboard RAM.
-
product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Fibre Channel Simulyzer™ Products
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
-
product
Microcontrollers
32-bit Qorivva microcontrollers based on PowerArchitecturetm e200 cores, that can run up to 264MHz. These devices include flash and RAM memory, as well as a number of external interfaces making them suitable for Aerospace & Defense of applications.
-
product
Raspberry Pi Zero w/ Wireless LAN & Bluetooth
Raspberry Pi Zero W
Full feature list for Zero W: 1GHz, single-core CPU. 512MB RAM. Mini-HDMI port. Micro-USB On-The-Go port. Micro-USB power. HAT-compatible 40-pin header. Composite video and reset headers. CSI camera connector. 802.11n wireless LAN. Bluetooth 4.0. We imagine you’ll find all sorts of uses for Zero W. It makes a better general-purpose computer because you’re less likely to need a hub: if you’re using Bluetooth peripherals you might well end up with nothing at all plugged into the USB port. And of course it’s a great platform for experimenting with IoT applications.
-
product
PCMCIA Card
DAS-429PCMCIA/RT10
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Touchscreen Panel 1.9GHz PC for Harsh Environments
PPC65B-1x series
Advanced IP65-rated Panel PC delivering high reliability and an extended operating temperature range in a thin, fanless design. The PPC65B series offers a rugged design for extreme environments and industrial IoT applications ranging from -20ºC to +70ºC. 1.9 GHz Quad-Core Intel® Atom™, E3845 processor, Up to 8 GB of RAM, Supports Linux, Windows 10 Operating Systems, Fast Graphics at High Resolutions • Five-wire resistive touchscreen • Resolution: 1024 x 768 / 1280 x 1024; 5 screen sizes 10.4" - 19".
-
product
ARINC 429 Test And Simulation USB Module
USB-429
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
Logic Analyzer
LAP-C(162000)
Zeroplus Technology Corperation
Bandwidth: 75MHzRange of the Trigger Voltage: -6V~+6VResolution of the Trigger Voltage: ±0.1V, RAM Size: 64MbitsMemory Depth per Channel: 2Mbits (Max 512Mbits for compression)
-
product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
MIL-STD-1553 One-Channel PCI Board
BRD1553PCI-1
The P-Orchestra™ is a one-channel MIL-STD-1553B PCI board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability. The board can be used as a hardware and software development kit for IP cores. P-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 16K word of internal RAM.
-
product
PCI Data Acquisition Boards
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
product
16 SE Or 8 Diff. Input Channels, 8 Analog Current Output Channels, PCI Express
APCIE-3121-16-8C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Direct Digital Synthesis (DDS)
Analog Devices’ world leading direct digital synthesis ICs incorporate features such as on-board comparators, RAM, PLLs, mixers, and registers. This makes them an ideal agile frequency synthesizer solution in systems for communications, test equipment, and radar.
-
product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
product
RightMark Memory Analyzer
RMMA
Before this test packet was created there was no proper software for measuring vital system parameters such as CPU/Chipset/RAM providing steady and reliable (reproducible) test results and allowing for changing test parameters in a wide range. Vital low-level system characteristics include latency and real RAM bandwidth, average/minimal latency of different cache levels and its associativity, real L1-L2 cache bandwidth and TLB levels specs. Besides, these aspects are usually not paid sufficient attention in product technical documentation (CPU or chipset). Such test suite, which combines a good deal of subsets aimed at measuring objective system characteristics, is a must have for estimating crucial objective platform parameters.
-
product
Memory Testing
C.C.P. Contact Probes Co., LTD.
Standard and Custom test solutions for RAM, Flash and many other memory chips.
