Filter Results By:
Products
Applications
Manufacturers
Power Quality Analyzers
test for noise, surges, power failures, impulses, and other parameters which cause poor quality power. AKA: PQA
See Also: Power Quality, Power Quality Recorders, Power Quality Monitors, PQA
- Virginia Panel Corporation
product
High Power, Contact, ITA, 150 Amps, 2 AWG
610150101
Primary mating contact 610149101. (May mate with other Receiver contacts, as well.)Specifications Operating Current 150 Amp Continuous using 2 AWG wireContact Resistance 0.35 mOhmsOperating Voltage 600VDC or Peak ACContact Body Cu alloyIP Tip - ThermoplasticContact Plating 30µ" Au over 100µ" NiOperating Temperature -40°C to +125°CT-Rise +40°C at 150 Amps+30°C at 125 AmpsContact Termination CrimpCycle Life 10,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.39
-
product
Power Quality Analyzer
PQM-703
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
product
Power Quality Analyzer
High-precision Power Quality Analyzer and MeterThe Dewesoft power quality analyzer can measure all the power quality parameters according to IEC 61000-4-30 Class A. In comparison to other power quality meters ours are able to do more detailed power quality analysis. Raw data storing, behavior at faults, calculation of additional parameters, etc.
-
product
Wave Quality Analyzer
APQM-707
This equipment is a power quality analyzer according to the European standard EN 50160. The Amperis APQM-707 is a high-tech product that allows universal measurement of the parameters of 50/60 Hz electrical networks, as well as the analysis and recording of these parameters.
-
product
Power Quality Analyzer & Motor Analyzer
438-II
The Fluke 438-II Power Quality and Motor Analyzer adds key mechanical measurement capabilities for electric motors to the advanced power quality analysis functions of the Fluke 435 Series II Power Quality Analyzers.
-
product
Acoustic Analysis
Noise is increasingly the subject of new regulations for the protection of human health and safety as well as for improving the environment in general. As well as sound levels, the perceived sound quality of products from washing machines to vehicles is often an important part of the customer buying decision so must be considered during product development. m+p Analyzer for noise and vibration measurement and analysis provides a full range of capability for these applications. Real-time fractional octave filters satisfy all acoustic applications from simple sound pressure, sound power for equipment legislative requirements, intensity mapping to isolate sources to sound quality metrics for product refinement.
-
product
Power Analyzers
At PCE Instruments you will find a power quality analyzer to measure the power in W, kWh or to analyze and measure harmonics. This power analyzer is a multi-function power analyzer device that measure precisely direct current, alternating current, AC-voltage, DC-voltage the intensity of DC or AC, phase rotation and idle, apparent and effective power. The reading of AC power is considered the real value and has a maximum range of 6000 Watts. While a reading is being taken, the polarity changes automatically, if negative values are taken then a minus sign will appear on the device display.Nowadays, power quality analyzers have many features such as, insulated current input, measurement of harmonics, AC and DC current measurement, AC and DC voltage measurement, frequency measurement, phase rotation measurement and idle, apparent and effective power measurement. All this data can also be logged and analyzed with the delivered PC-Software. Power analyzers of the type PCE PA 6000 can determine the energy in single-phase systems.Power quality analyzers of type PCE-GPA 62 allow the energy measurement in symmetrically loaded three-phase systems. Power analyzers of type PCE-PA 8000, PCE-360 and PCE-830 support professional power and energy measurements in single and three-phase systems.Apart from being used as energy-measuring devices, power analyzers like the PCE-830 can also be used for network analysis and the determination of harmonics and phase rotation. On our website you will find other power analyzers used in the field of electronics.
-
product
NanoVIP® CUBE™
NANOVIP® CUBE™ is a modern, powerful, S-Class portable network analyzer developed for professional analysis of consumption and power quality of the most complex electrical networks.It can be used on single-phase, two-phase, three-phase (balanced and unbalanced) networks, low and medium voltage.The advanced features and analysis software supplied makes it a suitable tool to the most demanding professional needs.Your product description goes here.
-
product
Power Quality Analyzer
PQM-711
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
product
Advanced Power Quality Analyzers
PM174-175 Series
SATEC offers various products to fit the special needs of each market.
-
product
Power Quality Analysis Pad
Weshine Electric Manufacturing Co., Ltd
Intelligent Three-Phase Harmonics Power Analyzer Portable Large LCD Screen Power Quality Analyser
-
product
Power Quality Analyzer
Beijing GFUVE Electronics Co.,Ltd.
Used to continuously monitor and analyze electricity lines for disturbance.
-
product
Handyscope TP450-50XM-W5
TP450-50XM-W5
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
product
Power Quality
Rishabh Instruments Pvt. Ltd.,
A compact state of art Power Quality Analyzer designed for utilities, as well as for industrial & commercial customers. It can continuously monitor power quality in accordance with EN50160, also the built in flexibility allows the user to set customized setting.
-
product
Test & Measurement
NIF (Dutch Instrument Factory, later Nieaf-Smitt) started in 1900 as one of the first organizations in the world with the design and production of instruments for electrical values. The portfolio of test tools, digital multimeters, current clamps, device testers, installation testers and power analyzers is characterized by quality and reliability.
-
product
Dial Torque Analyzer
MTS-Series
Dial Analyzer is designed for hand tools, like torque screwdrivers and torque wrenches. This tool is not suitable for power tools. Ideal for checking torque tools on production floor daily or weekly to ensure the tools aren't falling out of calibration, or can be used in cailbration lab. Using a quality torque tester makes a safer world through accuracy and precision. Measuring torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures.
-
product
Power Quality Analyzer
Power quality analyzer is a product carefully developed by our company and specially designed for field test of three phases, multi-functional and intelligent, man-machine operation and concise and comprehensive test instrument. It is easy to use, large LCD screen display, high resolution, interface in both Chinese and English, shock-proof shell structure and so on. Can simultaneously measure the 4-channel current (ABC three phase and neutral wire current), 4-channel voltage (ABC three-phase voltage and neutral line voltage to ground), the peak value of current voltage, maximum/minimum value over a period, three-phase imbalance factor, short-time voltage flicker, transformer K factor, active power, reactive power, apparent power, power factor and displacement power factor, active power, reactive power, apparent power, total harmonic distortion and harmonic, etc; Display real-time waveform, harmonic ratio bar charts of current voltage; Dynamically capture instantaneous change of voltage current, monitoring starting current, monitoring the power parameters and generate the alarm list, generate the trend chart for a long time record test data.
-
product
Power Quality Analyzer
Weshine Electric Manufacturing Co., Ltd
Three Phase Power Quality Analyzer High Precision
-
product
Power Analyzers - Meters - Loggers
Full line of power and power quality analyzers, loggers and meters including for extending measurement ranges. The wide range of applications include electrical monitoring, harmonic detection & analysis, utility testing, energy management, power factor analysis and correction, power demand and consumption, kW measurement, industrial power systems, and commercial maintenance.
-
product
Complete Power Quality Analysis System
PK4564
PK4564 complete Power Quality Analysis System includes PS4550 Power Quality Analyzer with extended memory, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, CAS3 hard-shell carrying case, PSM-A Software, and 1-year deluxe warranty.
-
product
Advanced Power Quality Analyzer
PM174
The PM174 answers the needs of a wide range of users within the ANSI Market: substation operators, electrical energy system integrators, generator users, industrial and commercial energy consumers. This analyzer covers the entire range of applications demanding high performance power quality monitoring and root cause analysis.
-
product
Power Quality Analyzer
APQM-700
*4 current inputs, physical current measurement on the neutral conductor.*Recording of up to 1100 parameters, including average, maximum, minimum and instantaneous values*Built-in heater, stable operation at low temperatures down to -20ºC.*Internal rechargeable battery, meter autonomy (min. 6 hours)*Ingress protection IP65, possibility of working in rain, snow and high humidity.
-
product
Advanced Power Quality Analyzer
PM175
The Advanced Power Quality Analyzer PM175 is a compact, multifunctional 3-phase power and revenue meter equipped with advanced power quality analysis capabilities.
-
product
Three Phase Electrical Power Calibrator
6003A
The Fluke Calibration 6003A Three Phase Electrical Power Calibrator is the most cost-effective way to get the superior accuracy and performance of three independent phases in one instrument. It is an ideal solution for calibration laboratories, electronics manufacturers, electric utility meter shops, and other organizations that manufacture and maintain energy meters, power quality analyzers, and similar tools.
-
product
Multifunctional Meter
CPM-70
Chuan Sheng Electronics Co., Ltd.
CPM-70 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication.CPM-70 series meters are able to measure bidirectional, four quadrants kWh and kVarh.It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2 MB flash for data-logging.
-
product
Analyzer Probe
Net-200
The NET-200 B analyzer probe is an integral part of the NET-xTVMS, the real-time monitoring of IPTV services quality. Intended for locations at the core, edge, subheadend, etc., the NET-200B is designed to function autonomously for an extended period of time should communication with the NET-ESVR Enterprise Server be interrupted. The NET-200B is running under stable and safe Linux OS on server class computers, powered by AC or DC sources, with optional power redundancy.
-
product
Portable Spectrum Analyzer
LPT-3000 Portable Spectrum AnalyzerThe LP Technologies LPT-3000 Spectrum Analyzer is a fully synthesized RF Spectrum Analyzer featuring simple user controls which allow the novice or the seasoned expert to use the LPT-3000 right out of box. The LPT3000 provides you with a powerful RF test and measurement tool for CDMA and WCDMA RF systems, broadcast RF systems, EMI/EMC. The features include 6.4 color display, centronics printer, internal memory, USB host, built in CDMA measurement (ACP, Channel Power and Occupied bandwidth). The LPT 3000 Spectrum Analyzer gives educational institutions, mobile and communication system manufactures and RF product service centers a quality RF test instrument at an unbelievably affordable price.
-
product
TorqueLab® Torque Analyzer
LTT-Series
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained. The LTT-Series is an advanced torque testing and documentation solution. Using a quality torque tester makes a safer world through accuracy and precision. Controlling torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised.
-
product
Power Analyzers
Power Analyzer can be used in any company that produces equipment consuming electric energy. Optimizing energy consumption not only protects the environment but also results in higher product quality. Power Analyzer are therefore excellent tools for research, development, quality control, maintenance and education.
-
product
Power Quality Analyzer
PS4550
The PS4550 is a true hand-held three-phase power quality analyzer with the features and accessories to achieve success in your power monitoring study. Its ergonomic contoured case, rugged construction, and small size make it ideal for field work. In addition, being part of the PowerSight “Start-To-Finish Monitoring Solution”, it has unique features and accessories that you will not find elsewhere.
-
product
Power Quality Analyzers
The Dewesoft power quality analyzer can measure all the power quality parameters according to IEC 61000-4-30 Class A. In comparison to other power quality meters ours are able to do more detailed power quality analysis. Raw data storing, behavior at faults, calculation of additional parameters, etc.
