Filter Results By:
Products
Applications
Manufacturers
Level
high or low along a bead it's a measure referenced.
See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test
- Pickering Interfaces Inc.
product
PXI 8 Slot BRIC 165x16 1-Pole (11 sub-cards)
40-561A-121-165X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
product
L20 Series Side Mounted Stainless Steel Liquid Level Switch
L20-02-S2-02-NO
The L20 Series Side Mounted 316L Stainless Steel Liquid Level Switches are commonly used in potable water, hot water, various acids, and in solvents. The side mount provides added versatility, allowing the switch to be used as a high or low level indicator, and stainless steel body provides use up to 500 PSI.
-
product
Entry Level Laser Source
SLS-21
SLS-21 series Stabilized Laser Source paired with ShinewayTech optical power meters can meet the test requirements of fiber identification, attenuation/loss measurements, continuity verification and transmission quality evaluation on singlemode and multimode fibers in LAN/WAN/CATV systems, offering high quality, stability and competitive costs.
-
product
Magnetic Float Type Liquid Level Gauge
HR9210
HighReach Measuring & Controlling System Co.,Ltd
The HR9210 magnetic float type liquid level gauge is a measuring instrument that reflects the measured liquid level or interface by the magnetic float as the sensing element and through the coupling of the magnetic float and the magnetic body in the display color strip.
-
product
Stealth Vent Tube Metal Detector
Stealth Vent Tube metal detectors are custom manufactured to integrate into any bottling application. The Stealth detects Vent Tube nozzles and metal contaminants in filled plastic or glass bottles of up to 3 liters/6.5 pints capacity. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
product
Gas Analyser
LT GasAnalyzer
Highly performant analyzer for measuring the concentration of technical gases based on a thermal conductivity sensor, an infrared sensor a para magnetic sensor or combinations of these sensors. Sensors are precise, robust and have a low cross-sensitivity. Extractive online measurement of the concentration of flammable or non-flammable gas components in gas mixtures. Can measure trace oxygen (O2) levels in the parts per million (ppm) range.
-
product
Single Frequency CW 532 NM Laser up to 18W
EQUINOX
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed system is inherently stable with low noise levels <0.05 % RMS and ultra-stable output powers with ±0.5 % stability. Equinox has options of high output power up to 18 W. Other major applications include mixing source, pump source for dye lasers and frequency doublers, optical tweezers, and biomedical imaging.
-
product
Firmware for High-speed HDLC Mode
OP-FW10G
OP-FW10G is an expansion firmware to upgrade LE-3500 measuring Bit-Synch (HDLC/SDLC/X.25/CC-Link) and SPI communications up to 10Mbps. Hardware processing by FPGA built in the analyzer makes it possible to capture data with time stamp at micro second. It is useful to analyze SPI communications and High-speed HDLC communications such as RS-485 multi-drop CC-LINK and TTL signal level on the printed-circuit board.
-
product
Data Acquisition and Logging, Multimeter System
DAQ6510
Creating a new level of simplicity, the DAQ6510 has a touchscreen user interface that enables faster setup time, real time monitoring of test status, and detailed data analysis on the instrument. See all digital multimeters »
-
product
Multiparameter Analyzers
Multi-parameter analyzers can be used in processes such as wastewater treatment, drinking water supply and is necessary to support life and treatment developments. In addition, the meter can be used in research institutions, and at a variety water quality related production sites in the mining, agriculture, forestry and fishery industries, for measuring the ionic concentration and various laboratories for the researches, drug manufacture processes, agriculture to measure the salinity levels of surface water and of soil samples, environmental protection, cosmetic industry food processing
-
product
LED Type Wafer Alignment Sensor Controller
HD-T1
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
product
Code Integrity
JScrambler
If you develop a security sensitive Web Application we believe that you don''t want to give any bonuses to possible attackers. JScrambler enables you to conceal as much as possible, the logic of your application, such as what information is gathered from the user, how it is processed on the client-side, how it is sent to the servers-side. Since our obfuscation introduces a certain level of randomness, it allows you to explore code morphing techniques, which can be vital in precluding attack automation.
-
product
Programmable High Voltage Tester
The high Voltage also known as di-electric withstand tester comes with customized facilities like voltage rampup rate zero interlock, Plus the user may specify the voltage level and leakage milliampere level so as to suit its testing needs.
-
product
Sonar
Piezo elements are used in military and commercial sonar systems for position finding activities. Location of surface and subsurface vessels, depth measurement, surveying, fish location, and communication are several of the more common sonar applications. Piezoelectric ceramic materials have high bandwidth and can quickly respond by applying high force at low power levels. These materials are generally unaffected by environmental factors such as humidity and temperature. CTS materials can be formed to customer specifications and are available in a wide range of geometries with dimensions up to 150 mm or thicknesses less than 100 microns. Our materials sustain high levels of drive voltage and provide excellent coupling factors in sonar applications.
-
product
Online UPS
LEVELUPS SERIES 10 - 1000 kVA
LevelUps series with Innovative 3 Level Technology is a true on-line double conversion, three-phase UPS system that provides one of the highest level energy efficiencies in the industry.
-
product
HV Rotary Switches
B-1003
A key feature of our rotary switches is their simple mechanical design which results in conservative stress levels for trouble-free, long life use. In addition, each rotary switch has a reinforced chassis design utilizing G-10 or G-11 fire retardant anti-tracking coated epoxy glass insulation. G-7 silicone glass is used for special applications where RF or high temperatures are involved. Heavy duty contacts, specifically designed to minimize corona in the Ross rotaries, are made of highly conductive yet weld resistant alloy with high contact closing force. This high force gives our rotary switches high momentary current capability and a reputation for their ability to withstand high shock and vibration as well as other severe environmental conditions. Ratings to 150kV, to 200A. When immersed in insulating oil, fluid or gas, the voltage withstand value is at least doubled and the interrupt capability is much greater. In a gas atmosphere, no modification is required. However, immersion in oil or fluid may require modification in some cases, at an extra cost (optional). Each unit is either manually or electrically operated. One SPDT contact is standard on most units. The auxiliary contact is used as an interlock for protection against "Switching Hot".
-
product
Vehicle Testing Technology
Maschinenbau Haldenwang GmbH & Co. KG.
Vehicle testing technology includes products for testing axle damping, wheel arches and axle and joint play. Diagnostic devices for eg the sound level or clamping force also make their contribution to the targeted assessment of the vehicle condition.
-
product
Level AFM
Is a flexible Atomic Force Microscope for scientists. It offers a wide range of modes, sophisticated spectroscopy options and the programming of user defined experiments. Besides standard options found in Anfatec's other AFMs, the level AFM allows to add Anfatec's full range of AFM options, such as KPFM, closed loop operation, automated sample motion, acoustic enclosure, humidity and temperature control ... Each instrument is adapted to the user's specific needs.
-
product
Hopper Ash Level Thermocouple System
HALT
The Hopper Ash Level Thermocouple (HALT) System is a preventative maintenance and safety tool that continually monitors the levels of ash within a hopper. As the hopper plugs and the ash levels increase, the thermocouples will become insulated from the boiler heat by the ash. Low temperature readings trigger visual and digital alarms which indicate that the hopper has plugged.
-
product
High Performance Carbon Isotope Analysis of LC Separated Compounds
LiquiFace
Elementar Analysensysteme GmbH
Compound specific isotope analysis of aqueous samples by LC is highly advantageous for those compound classes which are thermolabile or require derivitisation prior to GC analysis. Samples such as carbohydrates, amino acids, alcohols, organic acids and peptides make ideal candidates for LC-IRMS and the technique has been employed to great success in food and biogeochemistry applications. The LiquiFace works as an interface for the LC system to provide quantitative on-line conversion of organic carbon to CO2 prior to analysis by the IRMS system. Isotopic precision, accuracy and linearity is exceptional due to the highly efficient quantitative conversion of the organic carbon to CO2. This level of performance means that the LiquiFace is able to cover a range of sample types with a complete independence upon sample concentration, making the analysts life even simpler.
-
product
Linear Bench or Rack Mount Power Supplies Programmable, Local Control, Ultra Low Ripple/Noise
Series PTR
SERIES PTR are operationally programmable power modules that can be programmed to any level within their rated range and fully loaded at any output setting. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Hardy Shaker
HI-913
This Hardy Shaker provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting a test easier. A test can be conducted on a vibration transducer and manually recorded. Multiple tests are not saved; for multiple tests use the HI-903 or HI-803 units. The HI-913 is used for testing from 7 to 10,000 Hz, it offers adjustable frequency and vibration levels. This provides a reference source for verifying the accuracy of vibration transducers, connectors, cabling and instruments or instrumentation systems. The HI-913 has a ruggedized suspension system that can support heavy transducers (up to 800 grams - see frequency limits in the manual). The HI-913 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
product
Full HD Surgical Monitor Series
ASM24FHB
The ASM24FHB Series of medically certified FHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
product
Enlarge Environmental Chamber
REXMED REC-450
MOD. REC-450, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,644 Watts, 12,433 BTU/hr, 3,140 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
3.5" Single Board Computer
RSB-4810
Advantech’s RSB-4810 is an Arm-based 3.5" single board computer (SBC) powered by Rockchip RK3568 SOC. It leverages 4 x Arm Cortex-A55 cores, a 1.0 TOPs NPU, and a Mali-G52 graphics engine. RSB-4810 provides USB 3.0, PCIE 3.0, SATA 3.0, 2 x Gigabit Ethernet ports, a single channel LVDS (shared with MIPI-DSI), 6 x UART, and 2 x CAN for embedded applications. RSB-4810 also features Mini-PCIe, M.2 E-Key, and SIM card slot for Wi-Fi 6, BT, 5G/LTE, and AI acceleration modules. These features make Advantech’s RSB-4810 an ideal solution for entry level edge AI computing in AIoT applications.
-
product
PXI 8 Slot BRIC Solid State 352x8 1-Pole (11 sub-cards)
40-563A-121-352X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Terrestrial Signal Finder
Satlink WS-6905
Jointron(Quanzhou)Industry Co.,Limited
1.Satellite TV Equipments Including satellite receivers, satellite signal level meter, satellite finder(meter), HD DVB-S2 Receivers, DVB-S2 Meter with Spectrum Analzyer(in real time) 2.Terrestrial TV Equipments Inlcuding DVB-T receivers, DVB-T Meter, HD MPEG-4 DVB-T Meter, HD MPEG-4 DVB-T Receiver, SD MPEG-4 DVB-T Receiver 3.Combo Equipment: Including SD MPEG-2 Satellite&Terrestrial Combo Meter, HD MPEG-4 satellite&Terrestrial Combo Meter
-
product
Production Wafer Level Burn-in
TV19 VersaTile™ probe cards are designed with Celadon’s patented ceramic technology for superior electrical performance, yet is highly modular due to it’s 28mm x 28mm chassis. Micro-adjustments can be made in seconds with an allen wrench and a microscope. Easily align VersaTile cards for different wafer layouts using a 4.5” compatible 1×3 , 200mm, or 300mm VersAdjust plate.
-
product
Electromagnet System
Dr. Brockhaus Messtechnik GmbH & Co. KG
Electromagnet systems with different power levels to produce homogeneous magnetic fields. Usable for calibration of sensors, testing of magnet systems and Hysteresis measurement. Adjustable air gap from 0 up to 60 mm. Field strength in the air gap up to 3 Tesla. Software program for control and evaluation.
-
product
Advanced 3D Automatic X-Ray Inspection
V810 S2EX
V810 is "3D Automatic X-ray inspection System" that corresponds to the double side mounting SMT-PCB that is not able to be checked by a transmission-type X-ray machine. It has the ability to detect a wide range of defects, and It have 100% complete defect detection capability in the Hip-defective.And, it is the inspection machine of world's highest level that combines the ability of the ultra-fast test speed and the lowest false call positives further.
