Filter Results By:
Products
Applications
Manufacturers
Gold
invaluable naturally occurring material able to withstand corrosion, highly conductive. AKA: Au
See Also: Precious Metal, Platinum, Au, Gold Test
- Virginia Panel Corporation
product
Coax, Contact, Receiver, 20/26 GHz, Flex 402
610102119
Coax contact, Receiver, 20/26 GHz, Flex 402 (Only available in patchcords).Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield-SolderInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.25 for 2 - 18 GHz1.30 for 18 - 26 GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications Flex 402 (Only Available in Patchcords)Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition AInsulation Resistance 2000 MΩ Min.
-
product
Coherent Optical Receiver
IQRX
The IQRX is a “gold standard” coherent receiver for the measurement of coherent modulation formats such as QPSK, 64QAM and OFDM.Its high-bandwidth, low-noise architecture makes it ideal for high-quality, low-distortion coherent signal measurement.With two built-in lasers and convenient touchscreen LCD front panel control, the IQRX delivers quick and reliable measurements.
-
product
Trace Moisture Analyzer
Model 8800P
Teledyne Analytical Instruments
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis. All Al2O3 sensors share the same basic operating principle: the capacitance measured between the sensor’s aluminum core and gold film deposited on the oxide layer varies with the water content. The 8800 series moisture sensor employs unique Hyper Thin Film (HTF) technology, which offers three major structural improvements in Al2O3 sensor design. These structural changes, noted below, provide the user with increased sensitivity, greater stability and a quicker response time when compared to other conventional aluminum oxide sensors on the market today.
-
product
Probe Card PCB's
DTS offers both generic and custom PCBs blanks for probe cards. Probe card PCBs are available for all tester platforms and can be configured for any vertical technology, epoxy cantilever and legacy blade cards. DTS probe card blanks are made to precise specifications required for all probing technologies and are available in high speed and high temperature materials. All probe card PCBs employ a balanced layering construction to maintain tight flatness specifications and minimize warping, allowing good probe planarity. Gold plating on all surface metals facilitates easy soldering and minimizes probe resistance. DTS is continually adding new probe card blanks to its library!
-
product
Alchitry Cu FPGA Development Board (Lattice ICE40 HX)
If you are not needing a lot of power to start your FPGA adventure, or are looking for a more economical option, the Alchitry Cu FPGA Development Board might be the perfect option for you! The Alchitry Cu is a "lighter" FPGA version than the Alchitry Au but still offers something completely unique. FPGAs, or Field-Programmable Gate Arrays, are an advanced development board type for engineers and hobbyists alike to experience the next step in programming with electronics. The Cu truly exemplifies the trend of more affordable and increasingly powerful FPGA boards arriving each year. This board is a fantastic starting point into the world of FPGAs and the heart of your next project. Finally, now that this board is built by SparkFun, we added a Qwiic connector for easy I2C integration!
-
product
Circuit Breaker Testing
Weshine Electric Manufacturing Co., Ltd
Time measurement: 12 fracture intrinsic points, closing time, with the same period, phase with the same period.2. Reclosing measurement: each fracture closing - minute, minute - closing, minute - closing - minute process time, one minute time,one closing time, two closing time, gold short time, no current value.3. Bounce measurement: closing bounce time, bounce times, bounce waveform of each fracture, rebound amplitude of each fracture.
-
product
Extender
3690-6
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
-
product
Micro Coax, Contact, ITA, RG316 Double Shield
610141104
Primary mating contact 610140104. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - SolderInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 10.5 GHzVSWR 1.0225 +.05 f(GHz)Insertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
n-Line Jumpers on 0.100 [2.54] Centers
Series 152, 156 & 157
In-Line Jumpers on .100 [2.54] Centers. End connectors have Gold plated, solid Brass pins on .100 [2.54] centers. Available single-ended (Series 156), double-ended (Series 157), or bare-ended (Series 152). Reliable, electronically tested solder connections.
-
product
S-100 Bus, Vectorbord Plugbord
8801-1
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side) on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
product
Trace-Level Chemiluminescence NO/NO2/NOx Analyzer
Model T200U
Teledyne Advanced Pollution Instrumentation
The Model T200U Trace-level NO/NO2/NOx analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is designed to allow ultra-sensitive measurements with a lower detectable limit of 50 ppt while still meeting the requirements for use as a US EPA compliance analyzer.The Model T200U combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer.
-
product
Simulators (Gen II)
J1939
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
Extender
3690-12
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Power Supplies
ZPG-1200B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
Ring Disk Electrode
This ring-disk type electrode developed by NTT Advanced Technology Corporation is a form of printed electrodes. Users can choose them from Carbon, Gold and Platinum applied versions. Available as a working electrode of radial flow cells, achieves complete reduction/oxidation on the center disk at ultra-low flow rate because of its fine coulometric electrolysis efficiency. This also enables to analyze subsequent reaction as well as identification and quantitation of the sample at the same time.
-
product
Capacitance Bridge
1621
The GenRad1621 Capacitance Measurement system is a completely self-contained system capable of capacitance measurements in increments as small as 0.1 aF (10-4 pF) and conductance measurements in increments as small as 100 aU (10-7 U; equivalent to a shunt resistance of 1010 M). Measurements are three terminal, with 2- or 3-terminal connection, and provision is also made for the connection of an external standard for comparison measurements.
-
product
Sockets
Ironwood Electronics Sockets – Embedded gold plated wire elastomer (SG) – Stamped & Etched spring pins (SBT) – Embedded silver ball elastomer matrix (SM/SMP)– Compressible silver button in polyimide (GT/GTP)– Surface mount adapters for sockets (SF)
-
product
Plugbord
3719-1
VECTOR Electronics and Technology, Inc.
72 Gold plated edge contacts (36 each side)on 0.100"(2.54mm) centers. No circuit pattern edge contacts only.Unrestricted component placement over entire board surfaceRow and column legends provided
-
product
SD Express
SCHILLER AUTOMATION GmbH & Co. KG
The Standard SD Express Memory Card Test Adapters support PCIe® 16 GT/s (Gen4) and PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD8.0 and SD7.1. Minimal crosstalk, short trace lengths. The Micro SD Express Memory Card Test Adapters supports PCIe® 8 GT/s (Gen3) Interface Compliance Program testing for SD7.1. Minimal crosstalk, short trace lengths. They all support SDHC, SDXC, and SDUC operation modes Data collection via Lab Standard SSMP Test Cables and hard gold mating surface allow for high cycle count insertions and reliable performance.
-
product
Miniature Two-Point Probe Set
PRF-922B
The PRF-922B Miniature Two Point probe accurately measures point-to-point resistance of small areas. Like Prostat's PRF-912B Miniature Concentric Ring, the PRF-922B is capable of measurements up to 1.0x1012 ohms. Built-in distance stops provide consistent electrode to sample pressure for developing repeatable measurements. Use the PRF-922B to measure small material samples, hard to assess molded areas, edges of parts, tray or tape cells and other very small objects and surfaces. The assembly is supplied with replaceable conductive electrode covers to enhance contact resistance on irregular surfaces and composition materials. Thus, measurements may be made with either the gold plated electrode contacts, or via conductive rubber covers.
-
product
Small Pellets Testing Kit
The ceramic pellets that generally have a diameter between 6 to 12 mm and a thickness of 2 to 4 mm are blocked on a special flange with a disc of soft vermiculite (mica) that has the same high of the ceramic sample and prevents the latter (or the flanges) to toggle. Gold or other appropriate M_Grid™ materials are placed on both sides of the pellet for potential and current measurement. After this operation, the double ceramic felt caps are covering the sample as for any other cell mounting in the Open-Flanges™ test set-up.
-
product
Simulators
SAE J1708/J1587
The Au SAE J1708/J1587 simulators (Gen II, V1.00A release) can simulate up to 44 most frequently used Engine/Transmission/ABS parameters, warnings and diagnostic messages. Up to six Engine MID, three transmission MID and six ABS MID can be field configured. All editions can run independently (without personal computer). This family of simulators are designed very easy to use. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
Proprietary Software
WinFT
WinFT is our proprietary software which makes D&P instruments so functional and easy to winft1_largeuse. Based on the Windows operating system, this software provides simple and intuitive control of the instrument. All of the usual File functions are available, as well as controls over instrument settings such as resolution, apodization, zero-fill and number of coadds. Display options enable the user to display interferograms, spectra or both, as well as to adjust plot scales and units. Onboard math processing allows for real-time calculation of ratio, difference, and absorbance, and when using our calibrated hot-cold blackbody calibrators, the ability to measure calibrated radiance. Further, WinFT offers the ability to measure sample temperature in the radiance function by matching a Planck to the calibrated radiance. With the gold diffuse plate, the software can also compute and display absolute emissivity of samples. Our software also enables exporting of data files, now made even easier with our USB and LAN connections. In addition, the software has been designed to be easily run using the keyboard function keys and single letter commands, making the use of a mouse in the field optionalas well as minimizing key strokes when taking measurements in the field.
-
product
Process Carrier Pallets
Metalic Family
Process carrier pallets to carry the circuit boards through pick-n-place, IR reflow, gold wire bonding, epoxy dot encapsulating, and final fuctional test. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets. Process carrier pallets can be designed to carry your circuit boards through assembly, wash and final test.
-
product
Micro Coax, Contact, Receiver, RG316
610140101
Primary mating contact 610141101. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outerCable Specifications RG316Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Power Supplies
ZPG - SERIES
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
Plugbord
3662
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only.Unrestricted component placement over entire board surface
-
product
Mini-ITX SBC With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 Processor, Dual DisplayPort++, HDMI, LVDS, USB 3.0, MSATA, M.2 And Dual GbE LAN
MANO520
The MANO520 is powered by the LGA1151 socket 9th/8th generation Intel® Core™ i7/i5/i3 (code name: Coffee Lake), Intel® Pentium® Gold or Intel® Celeron® processor with the Intel® Q310 chipset (Intel® Q370 optional). The Intel® Coffee Lake-based MANO520 is specifically designed for performance-demanding applications with its excellent reliability as well as communication and real-time computing capabilities. The MANO520 supports two 260-pin DDR4-2666/2400 SO-DIMM sockets for up to 32GB of memory. Also, the mini-ITX motherboard features three SATA-600 connectors and one mSATA for additional storage. It is equipped with one full-size PCI Express Mini Card, one PCIe x16 and one M.2 Key E slots for wireless devices such as Wi-Fi, Bluetooth, and 3G/LTE. Moreover, the mini-ITX form factor single board computer features an ATX connector with AT mode auto power function.
-
product
Pressure Sensors
ESI Technology manufacture a wide range of pressure sensors using a variety of different technologies. Pressure transducers (voltage output), pressure transmitters (milliamp output), panel meters, accessories. Silicon-on-Sapphire technology and a titanium diaphragm combine to make the new Gold Standard in pressure sensing. Custom pressure measurement solutions have been integral to ESI’s success. All aspects of design and manufacture are done in-house at our UK facility. Impressive quality at an affordable price. So if you don’t see what you are looking for, just ask.
-
product
Mini Coax, Contact, ITA, RG178
610103157
Mini Coax, Contact, ITA, RG178.Mechanical SpecificationsDurability 20,000 cyclesContact Material Center conductor – BeCuShield – BrassContact Plating Shield 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance < 5 milliohms @ 0.5 Amp & always < 10 milliohmsCable Specifications RG178Environmental SpecificationsOperating Temperature -50C to +105CInsulation Resistance 1000 MΩ min.
