Filter Results By:
Products
Applications
Manufacturers
Electronics Test
Devices whose quality of operation is based on the effects of electrons.
- InterWorking Labs, Inc.
product
Test SIP
VoIP, Video, and IPTV products must withstand and continue to function when facing all the conditions that occur on the Internet. These include attacks from hackers exploiting vulnerabilities in security and protocols as well as the common phenomenon of congestion, delay, jitter, drops, and so on. VoIP, Video, and IPTV products must demonstrate robustness and resiliency in the face of unusual and/or illegal conditions.
-
product
Power Supply Test System
The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.
-
product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Electro-optic Test Bench for IR Detectors
BIRD 210
Testing detectors requires the implementation of ultra-low noise driving electronics and presenting high quality optical stimuli to the detector under test. This meets all these requirements and allows to test any type of detector by easily implementing the detector’s driving signals and providing exhaustive and accurate measurement results.
-
product
Electronics Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
product
IEC60529 Flushing Test Device IPX5/6
FC-2
Shenzhen Chuangxin Instruments Co., Ltd.
This Flushing Test device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005,etc. Accordance with requirements of IPX5/6.Applied to carry out waterprooftest on LED lamps, house hold appliances, electric and electronic products and other electric accessories.
-
product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
product
PXIe Digitizer: 100 MSa/s, 14 bit, 100 MHz
M3100A
The M3100A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
product
Components
Microwave Solutions is a worldwide leader in the design, development, and manufacture of RF and microwave components. Our broad line of components operate in the 100 kHz to 26GHz range and include Attenuators, BAW Devices, Detectors, Isolators and Circulators, Linearizers, Mixers, and VCOs. For over 50 years our components have played key roles in sophisticated airborne and satellite communications equipment, navigation and guidance systems, radar and sonar equipment, telemetry electronics, surveillance, and reconnaissance systems, and high performance commercial test equipment.
-
product
Simulation Systems
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
product
Multifunctional Immunity Test System For Automotive Electronics
EMS-ISO7637
EMS-ISO7637 automotive multifunctional immunity test system meet newest ISO7637-2 requirement of
. This standard was issued by international organization for standardization, and this system included all of ISO-7637 required test waveform and meet most of automotive manufacturer’s requirement for automotive electronic immunity test. -
product
Simulation And Training
With more than 25 years of experience, Textron Systems Simulation and Training provides comprehensive end-to-end training solutions for air, land, sea, space, unmanned and electronic warfare platforms. We design, develop, and support integrated training devices, classroom courseware, virtual, live and constructive training, and software solutions. Our products and services support advanced platforms including C-17 Globemaster®, B-1 Lancer, F-35 Lightning II®, F-22 Raptor® and other high-value assets. Textron Systems also produces electronic, RF, and/or multispectral test equipment for verification and validation of these and various other air, land, sea, space, unmanned and electronic warfare platforms.
-
product
RFID Test System
RFID test system of Peritec is making FPGA board (IF-RIO) the processing of the IF band. This reading of the code, called (Electronic Product Code) EPC is required for RFID tag ISO18000-6 TYPEC of (EPC C1 G2). However, it did not provide treatment too late in the traditional instruments.
-
product
Automotive Electronics Functional Test System
TS-5020
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
product
IC Pick & Place Handlers
Chroma's IC test and handler solutions assure that IC packaging meets the original design specifications and verify the performance of the IC before it is assembled into the electronic product.
-
product
Modular Power
RFP Controller
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Software
Electrochemistry Tests
Materials Development Corporation
CyclicVoltammetry and Galvanostatic Charging are tests used throughout the industrial and scientific communities to study chemical reactions and behavior of electronic structures. They are extremely helpful in the monitoring of nano based dielectrics, used in super /ultra capacitors or self-assembled monolayers (SAMs). The Cyclic Voltammetry test applies a ramping voltage to a device and measures the resulting current. In acapacitor-like structure the current reveals loss in the dielectric as well as degradation over time. CyclicVoltammetry is used to characterize the performance of supercapacitors and ultracapacitors formed using various nano-technologies. It is also useful in the studies of self-assembled monolayers used for sensors.
-
product
POWER PROBE 4
PP401
*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)
-
product
26.5 GHz Single-Mode Lightwave Component Analyzer
N4375E
The new N4375E single-Mode LCA is based on the latest 5222A series network analyzers with 2-port or 4-port configuration. This LCA is the ideal measurement solution for electro-optical components up 26.5GHz electro-optical components, as well as Radio over Fiber (RoF) and aerospace and defense (A&D) electro-optical test applications. The N4375D is traceable to international standards and provides guaranteed specifications for electro-optical responsively S-parameter measurements in a turn-key solution. In combination with N4691B electronic calibration kit you get fastest setup of your test, so you can focus on developing your components. The new N4375D replaces the industry standard 8703A/B series and supports specified modulation frequencies up to 26.5 GHz at 1310nm and 1550nm source wavelength or individual wavelength with external optical input.
-
product
Programmable Electronic Load
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
product
Gyro Test Panel
TA-256
Designed to test the KI256 / KI258 panel mounted Flight Director gyros. The panel contains a power supply, the special manufacturers recommended rate board required by SA-103 to properly verify outputs As well as all other electronics required to support by the book testing.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Test system for Electronic Device
PCB
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
product
Waterproof Test Chamber
JL-XC
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
product
Adapter/Stainless Steel
WADP-24MSM
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
IPX56 Simulation Rain Test Chamber
CX-IPX56A
Shenzhen Chuangxin Instruments Co., Ltd.
IPX56 Simulation Rain Test Chamber widely used in the lamps and electrical and electronic product certification testing institutions and for testing the waterproof of electrical and electronic products of shell protection level.
-
product
Adapter/Stainless Steel
WADP-NFNF-BH
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
product
Test Cell Measurement
Accurate Technologies’ long history in powertrain development provided insight into the day-to-day issues that were occurring during engine testing at a time when electronic devices were being introduced to monitor performance instead of traditional mechanical means. Outside of the harsh physical environments, devices used in these applications need to perform difficult high-voltage signal conditioning and high-speed synchronous pulse processing. ATI developed unique products that satisfy specific test cell or dynamometer challenges. These highly accurate products measure engine timing (IGTM) or speed (SmartTach) in convenient ways to provide information that otherwise may not be available.
-
product
Digital/Pattern/PE Card
PEMU32
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on theproven architecture of the PE32, the PEMU32 offers highvoltage PMU/DPS and pin electronics in a compact, 3UPXI form factor. Each card can function as a stand-alonedigital subsystem or if required, multiple cards can beinterconnected, supporting up to 256 bi-directional pins(8 boards). The PEMU32 also supports deep patternmemory by offering 32 M of on-board vector memorywith dynamic per pin direction control and with test ratesup to 10 MHz.
-
product
Crack Testing
STATOGRAPH® Product Family
Foerster Instruments, Incorporated
The STATOGRAPH product family is used for testing surface cracks with the help of eddy current sensors. Eddy current testing for material cracks requires the appropriate evaluation electronics and probes adapted to the testing task. Depending on the test situation and test object, the STATOGRAPH family of test instruments offers the right system for this purpose.
-
product
Flexible Test Connectors
Pin and socket sizes 22, 20, 16, 12 and 8 conform to MIL Spec dimensions. Whenever connector reliability is important, you’ll find NASA-approved FLEXCON test connectors. Applications include electronic, electrical and communications systems, computers, space vehicles, missiles, aircraft and other military equipment.
