Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
78-Pin D-Type Male Breakout DIN Rail
40-967-078-M
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-037-2m-MU
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Surge Voltage Generator
SSG 500
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 500. The SSG 500 surge voltage generator is arranged in a 19'' housing. Maximum safety is achieved with the electrical safety control unit, the automatic discharge unit, the fully enclosed design and separate protection and system earth.* 6 output voltages up to max. 16 kV available* Electromagnetically actuated surge switch* Preselectable surge energy: 288 / 512 Ws (in all voltage ranges)* Automatic discharge unit
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A037DM5-T-0A100
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Electrical Safety Tester
MACROEVTEST
Multifunction instrument for electrical installation safety testing, power quality analysis and EVSE safety testing
-
product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
20-Pin GMCT Cable, Male to Unterminated, Ferrules, 10A, 2m
A020GMR-F-0C200
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
Hipot Tester
HAL
The HAL Series combines over 50 years of expertise in ensuring the electrical safety of manufactured electrical products.
-
product
RCD Tester
CZ20053
Protect yourself and your employees by ensuring that your portable electrical appliances and equipment are tested for electrical safety to AS/NZS 3760:2010 with the RCD Tester. The CZ20053 Aegis RCD Tester is an essential piece of equipment for every workplace.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Tinned Ends, 1m
A025DF4-T-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Partial discharge measurement with remote wireless reading
PD-LT
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
Dry Arc Resistance Tester
Dry Arc Resistance Tester is designed to conduct high voltage,low current Arc Resistance test on solid electrical insulation material as per:ASTM standard D495-99 (2004) and UL 746A. Why Arc Resistance Test? Many Cases of insulator failure are due to deterioration of its surface because of sustained electrical discharge or Arc. This test method is intended to test the resistance of insulating material when a high -Voltage low -current Arc close to the surface of insulation, intending to form a conducting path therein or in causing the material to become conducting due to decomposition and erosion.AdvantagesThis Test ensures that your products meet high standards of quality & safety. This product is meant for all Switchgears/ insulator/ Polymer/ electro plastic manufacturers and manufacturers who use insulators in their products e.g. Wiring Accessories, Appliances, HT/LT line insulators etc.
-
product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 3m
A020GFR-C-0C300
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
Medical System
Sentinel III
Chroma Systems Solutions, Inc.
The Sentinel III System provides complete Electrical Safety Testing to IEC60601-1 and IEC 60601-2-49 (Multifunctional Patient Monitoring Equipment) in a fully automated fashion. The Sentinel III saves time by scanning patient connections for leakage current without powering down the device.
-
product
Electrical Safety Tester
JUPITER
Multinfunction Multimeter for electrical installation safety testing.
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
Downloadable PAT Tester
Apollo 500+
The Apollo 500+ features a comprehensive range of electrical safety tests with user configurable test sequences and checklists for PAT, PPM and PPE. It has storage for up to 10,000 test records and is compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
product
Automated Test Systems
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
product
Combination Measuring Devices According to DIN EN 61557-10 (VDE 0413-10) are permitted
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
product
20-Pin GMCT Female Connector, 16A, Without Backshell
92-960-020-16A-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 14 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Product Safety Testing & Certification
MET has been certifying, listing, and labeling products for electrical product safety for more than 40 years. In that time, MET has certified thousands of products for compliance to electrical safety standards. This translates into literally millions of products sold in the U.S. and Canada labeled with the MET Mark.
-
product
9-Pin D-Type Female Connector
92-960-009-F
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
product
Hipot Tester
STM/L
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
product
Grid-Connection Testing System
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 1m
A037DF4-C-0A100
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Testing of Electrical Safety
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A025DM5-C-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Multifunctional Testers
Electrical installation safety is nowadays more important than ever with the proliferation of increasingly complex domestic electronic appliances people install in their homes that require reliable power supply lest they become damaged and pose a fire and electrocution risk. Effects of unreliable and even dangerous electrical installations are even more acutely felt in industrial environments where they translate into production losses.
-
product
37-Pin D-Type Male Connector Block
40-965-037-M
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Hipot & Safety Test
Chroma Systems Solutions, Inc.
Electrical safety tests to comply with IEC, UL, TUV, CSA, EN, and other electrical safety requirements.
