Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
8-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 1m
40-972-408-1m-FU
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
TRMS DC/AC Clamp Meter
KT-2000T
Jaw size:ф40mm,50×70mm (max)3 3/4 digits LCDAuto Power Off, Auto RangeTrue RMSMax. 2000A (DC/AC)Frequency testCapacitance testDuty cycle 0.1%~99.9%Diode Test & Audible ContinuityKT-2000 without TRMS
-
product
Auto Ranging Clamp Meters
Ohm, Diode, Continuity, Capacitance, Frequency and Duty inputprotection to 600V DC/AC rms.Resistance measurement from 0.1Ω to 40MΩ.Diode test and Audible continuity check function.Frequency counter from 0.500Hz to 5MHz.Auto power off to preserve battery life.Display Back-Light feature.
-
product
AC/DC Laboratory Power Supplies
PeakTech Prüf- und Messtechnik GmbH
This AC / DC laboratory power supply has two separately adjustable outputs which can dispense AC/DC voltages from 0 - 30 V as well as DC/AC current 0 - 6 A. Due to the possibilities offered by this device, it is also suitable for the maintenance of small AC circuits, transformers and lights.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-800B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1000B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
DC-AC Power Inverters
Samlex America, Inc Power Supplies
Convert battery voltage into AC current similar to power supplied through a household electrical outlet.
-
product
SE-03 - Digital Clamp Meter
Jaw size:¦Õ6.8mm. One Touch Zero for DCA adjustment. Auto range, Auto power off,Auto polarity display. Auto zero adjustment, Auto units display,Data hold. High resolution DC/AC 10mA. Diode & Continuty test
-
product
DC-AC Inverters
The standard DC/AC inverters start at 125VA and rise to redundant modular systems capable of a 48kVA output. All our inverters give a true sinewave output and have proven themselves to be exceptionally reliable in numerous applications. Our DC/AC power inverters are provided in a variety of different case styles from wall mount, benchtop to modules, cassettes and 19" racks. A number of inverters can be built and approved to railroad and automotive standards. Stand-alone units are complimented by DC/AC inverters with built-in bypasses. The INV-TC3P is capable of providing 3-phase generation from a 48VDC supply.
-
product
AC/DC TRMS Clamp Meter
SE-02T
High resolution DC/AC 1mABand wide up to 20KHz23mm large jaw diameterTrue RMSOne Touch Zero for DCA adjustmentLarge 3 3/4 digits LCD (3999 counts)Auto range, Auto power off, Auto polarity displayAuto zero adjustment, Auto units display,Data holdDiode & Continuity Test,Capacitance Tes
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
High resolution Clamp Meter
SE-02
High resolution DC/AC 1mA. 23mm large jaw diameter. One Touch Zero for DCA adjustment. Large 3 3/4 digits LCD (3999 counts). Auto range, Auto power off, Auto polarity display. Auto zero adjustment, Auto units display,Data hold. Diode & Continuty Test,Capacitance Test
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-500B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
DC/AC Sine Inverter
44KS1
NAI's 44KS1 is a DC/AC Sine Inverter that accepts +28 VDC input and converts it to a 26 VAC sine wave at 65 VA power.
-
product
Low cost Multimeter
DMM 125
7 Functions, 27 Ranges. Auto and manual ranging. 34 Segment fast bargraph. Auto Power OFF to save battery. 10 Amps and mA DC/AC fuse protected
-
product
AC/DC Clamp Meter
SE-06
Jaw size: φ6.8mmLarge 3 3/4 digits LCD(3999 counts)One Touch Zero for DCA adjustmentAuto range,auto power off,auto polarity displayAuto zero adjustment,auto units display,data holdHigh resolution DC/AC 0.1mADiode & Continuity test
-
product
Bidirectional DC Power Supply + Regenerative Load
62000D
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
product
DC/AC Clamp Meter
SE-01
High Resolution DC/AC 10mA. 23mm Large jaw Diameter. One Touch Zero for DCA adjustment. Large 3 1/2 Digits LCD (1999counts). Auto power off,Data hold. Diode & Continuty Test. Capacitance Test
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
product
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps)
7-251914000-072
Power, Patchcord, ITA, 72", Micro Power, 14 AWG White, Single Ended ( 22 Amps).
-
product
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-036
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
product
Industrial AC Power Supply PS2 Form Factor, 350W
APS-935XA-EPS12
- Power (typical): 350W- Current Type: EPS12- AC Voltage Input Range: 110 - 220 VAC (±10%)
-
product
Intelligent Power Monitor
iPM
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
product
Switched Power Distributed Module, CAN Control
H730008xS
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
product
Analog Optical Power Meter - PXI
Power 1500 Series
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
product
PXIe-4154, 2-Channel, 8 V, 3 A PXI Programmable Power Supply
781155-01
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
-
product
Power, Patchcord, ITA, 36", Micro Power, 12 AWG White, Single Ended (22 Amps)
7-251912000-036
Power, Patchcord, ITA, 36", Micro Power, 12 AWG White, Single Ended (22 Amps).
