Filter Results By:
Products
Applications
Manufacturers
- Valhalla Scientific Inc.
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Test Kit
Metriso B530
Wolfgang Warmbier GmbH & Co. KG
Test voltage / Test current: 1 mA < I < 1,3 mAHigh ohmic range: DC 10 volts,100 volts and 500 voltsTest range:low ohmic range: 1 to 10 kOhmhigh ohmic range: 1 kOhm to 199 GOhmOperation: Battery operatedProbes:2x Model 870 (weight: 2,27 kg / ø 63,5 mm) with conductive rubber (grey) and extension,1x hand-held probe Model 45
-
product
Current Probe For Oscilloscopes
CP 1005
The CP 1005 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
product
Loop-Powered Transmitters and Drivers
4-20mA
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
product
600 Amp DC / 400 Amp AC Current Probe
DC600
Can measure from 5 to 600 Amps DC current for most industrial DC measurement jobsNo batteries required, because power is supplied by PowerSight. This means that the probe will not stop during a long monitoring session.
-
product
AC/DC Current Clamp Probe,DC~1MHz(-3db)
CP-07+
Can connect with Oscilloscope.AC/DC current Measurement.1mA to 4A test range.Bandwidth: DC~1MHz(-3db).Rise time:0.35μsNoise level: 2mAJaw size: 5mm max.Auto zero at power on.Relative zero correction.
-
product
Current Probe
DCFlex
Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
product
Complete Power Analysis System
PK3564-PRO
PK3564-PRO complete Power Analysis System includes PS3550 Power Analyzer, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, CAS3 hard-shell carrying case, PSM-A Software, Mini Line-to-DC Converter, Bluetooth Adapter, USB Communications Cable, and 1-year deluxe warranty.
-
product
DC Power Analyzer, Modular, 600 W, 4 Slots
N6705C
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
product
CC15010X, 10 MHz, 150 A Current Oscilloscope Probe
786849-01
The CC15010X, or Hioki 3274, is a clamp-on current probe that offers a wide DC to 10 MHz bandwidth and 150 A of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.
-
product
Probes, Clamp-On
EM-6987 | 1 KHz – 110 MHz
The EM-6987 is capable of measuring signals and noise superimposed on power currents up to 300 A from DC to 400 Hz. Intermodulation effects on current probe output are also negligible.
-
product
Cryogenic Applications
Over the last 20 years the Celadon Engineering team has developed an expertise in cryogenic materials which has resulted in a solid reputation in the industry for producing extremely stable cryogenic on-wafer probe card as well as DUT probing solutions. These custom cryogenic probe card solutions are widely used to test Space, Military, Medical and Quantum Computing products. Celadon’s cryogenic solutions vary from standard VersaTile™ footprints which interface to positioners to innovative custom PCB based designs to allow for flexibility when testing at these very cold temperatures. Lakeshore cryogenic wire is used in standard DC solutions for high density cableout designs to support high pin count applications. During the development process, Celadon works closely with the cryogenic prober vendor to ensure the integrated solution is optimized for current and future testing needs.
-
product
AC/DC Current Clamp Probe,DC~500kHz(-3db)
CP-07
Can connect with Oscilloscope. AC/DC current Measurement. 400mA ,2us, 4A,2us test range. Bandwidth: DC~500kHz(-3db)Rise time:1.5μsNoise level: ≤4mA(with average mode) or ≤20mA（DC~500KHz)Jaw size: 5mm max. Auto zero at power on. Relative zero correction.
-
product
AC / DC Current Probe, 10 MHz, 150 Arms
N2781B
The N2781B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 150 Arms continuous
-
product
AC/DC Current Probe,DC~100KHz
CP-05
Connected with Oscilloscope and DMMAC/DC current MeasurementAmorphous Alloy CoreTest range:4A,11us,40A,6us,200A,6us100KHz Noise:20mALow battery indicationSmall size Light weightJaw size:23mm(Max)
-
product
Gaussmeter
DX-105
DX-105 Gaussmeter is a desktop gaussmeter. Which is based on the latest progress of the Hall Effect magnetic field measuring instrument.Adapt the high stability constant current source circuit technology to design and manufacture. Test probe adapts imported GaAs linear Hall-chip, the difference between any two probes is small, which can be replaced directly when it is damaged. DX-105 Gaussmeter is an ideal DC magnetic field test instrument.
-
product
Current Probes
Teledyne LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology, Teledyne LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements.
-
product
Current Probe
DCP-BTA
Vernier Software & Technology, LLC
The Current Probe measures DC and low-frequency AC currents up to 600 mA. Use Current Probes in combination with Differential Voltage Probes to investigate Ohm's Law and explore series and parallel circuits. The 0.1 shunt resistor minimizes changes to your circuit. If currents will exceed 1 A, use the High Current Sensor.
-
product
Gaussmeter
DX-103
DX-103 Gaussmeter is a desktop gaussmeter.Which is based on he latest progress of the the Hall Effect magnetic field measuring instrument.Adapt the high stability constant current source circuit technology to design and manufacture. Test probes adapt imported GaAs linear Hall-chip, the difference between probes is small, which can be replaced directly when it is damaged, and is an ideal AC & DC magnetic field test instrument.
-
product
AC/DC Current Clamp Probe,DC~1MHz(-3db)
CP-07B
●Connect to Oscilloscope.●AC/DC current Measurement.●4A ,2us, 40A,2us test range.●Bandwidth: DC~1MHz(-3db). ●Rise time:0.35μs●Noise level: 5mA●Jaw size: 5mm max.●Auto zero at power on.●Relative zero correction.
-
product
DIGITAL TURNS TESTER AND DIGITAL LCRTZ METER
TURNS-LCRTZ
Digital TURNS TESTER with LCR for Counting / Measuring Number of Turns for Toroidal Coils , Current Sensor , Current Transformer , Round Core Coils. Can measure, Turns along with Winding Polarity , DC Resistance , Inductance (L), Capacitance (C), DC Resistance, Rac, Q, D, ESR and Tan.Toroidal Turns Platforms :TTPT100 : 5 T - 1000 T , TTPT1000 : 500T-10000 T The Platform has 2 connections for the coil and 2 for the probe wire. Measurement principle is based on dynamic comparison of the voltage across one turn and the coil. You will be able to get the polarity or winding indication with respect to the one turn reference.Accuracy : + 0.2% + 0.5T for high and medium permeability cores at suitable test frequency. Internal Diameter must be able to pass a wire as thin as 0.2 mm. External Diameter as high as 200 mm.Test Frequency Selectable in Step : 50 Hz, 100 Hz , 500 Hz, 1 KHz, 5 KHz, 10 KHz. Test Voltage adjustable : 100mV to 1V in steps of 50mV.
-
product
Digital Multimeters
Triplett Test Equipment & Tools
compact digital multimeter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Voltage, DC Current, Resistance, Continuity, Diode Test, Transistor hFE, and Temperature. The rubberized boot provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. The Model 1101-B is well suited for a variety of commercial and residential applications such as security, home theater, electrical, HVAC installations and more. Includes test leads with alligator clips, Type K bead probe and battery (9V).
-
product
LTP-72 High Performance Long Travel Probe
LTP-72
Current Rating (Amps): 6Average DC Resistance lower than (mOhm): 100Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 400Full Travel (mm): 10.16Full Travel Remark: Alternate Spring: 400 mil / 10,16 mm, High Spring: 350 / 8,89 mmRecommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 50,000Overall Length (mil): 1,850Overall Length (mm): 46.99
-
product
Oscilloscope Current Probe,DC~200KHz(-3db),40A
CP-05A
Amorphous Alloy CoreRange:4A,2us,40A,2usBandwidth:DC~200KHz(-3db)Rise time:1.75μsLow battery indicationNoise level: 15mA Jaw size: 23mm(Max)Auto Zero at power onRelative Zero correctionSize 180mm(L) X 44mm(w) X 30mm(H)Weight: Approx 200g
-
product
AC / DC Current Probe, 100 KHz, 100 A
1146B
The Keysight 1146B AC / DC probe provides accurate display and measurement of currents up to 100 A DC or peak AC / DC to 100 kHz without breaking the circuit. The 1146B AC / DC probe has hall-effect sensor technology to measure AC and DC signals. It is compatible with any Keysight oscilloscope with 0.2 to 0.5 V / div sensitivity and 1 MΩ BNC input.
-
product
Precision Picoprobe™ Micropositioner Probe Holder Kit
PHD-3001A
High Power Pulse Instruments GmbH
*Pulse force and pulse sense fixed pitch and flexible pitch RF probing solution for TLP/VF-TLP/HMM on-wafer measurements using Picoprobe™ Model 10*High peak current capability 80 A (100 ns)*DC – typ. 7 GHz bandwidth*Isolated probe-head ground shield for high pulse sense common mode signal rejection*Including fixed pitch replacement probe tip 50 Ω, right, 100 µm pad pitch*Including fixed pitch replacement probe tip 5 kΩ, left, 100 µm pad pitch*Including flexible pitch clamps plus 10-5k(0502)-125-W-1 and 10-50/30-125-W-1 replacement probe tips*True coaxial high-resolution 80:1 rotary probe-head for accurate probe tip adjustment
-
product
2000 Amp DC / 1500 Amp AC Current Probe
DC2000
Our DC2000 Current Probe measures up to 2000 amps DC (as well as 1500 amps AC). Self-powered via our meter, so there are NO batteries that can run down during a measurement session.
-
product
AC/DC Current Probe
CP 30
The CP 30 current probe has been designed for use with multimeters respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
product
High Impedance Active Probes
18C & 19C
High impedance probes, PICOPROBE® MODEL 18C and MODEL 19C, combine the most advanced MOS and bipolar technologies with special, low capacitance packaging techniques to achieve truly remarkable electronic measurement capabilities. While being manufactured each instrument is individually optimized for the best possible performance. The extremely low input capacitance, high input impedance, and almost negligible input leakage current permits the direct probing of even the most sensitive MOS dynamic nodes. At the same time, the full dc capability of this Picoprobe coupled with the high speed capability permits the full characterization of circuits.
-
product
AC/DC Current Clamp Probe,DC~5MHz(-3db)
CP-07C
●Connect to Oscilloscope.●AC/DC current Measurement.●Bandwidth: DC~5MHz(-3db). ●Rise time:0.7μs●Noise level: 10mA●Jaw size: 5mm max.●Auto zero at power on.●Relative zero correction.
-
product
N2782B AC / DC Current Probe, 50 MHz, 30 Arms
N2782B
The N2782B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
