Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to 68 Pin for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
product
3-m, 50-pin Dsub Cable
Y1136A
Connect this m/f twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
product
LAN Tester RJ45
CZ20250
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, and is a great Cat 5, Cat 6 and Cat 7 cable tester, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Cable Tester
CT100
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
product
3-m, 78-pin Dsub Cable
Y1138A
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
product
Mini Digital Clamp Tester (CE)
M-140HC
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy!:Measurale Load Current at high voltage CV/CVT cables with grounding lines for shield phase.*Epoch-Making!:Can measure phase current of CVT cable just by putting CT head on to the conductors as well as CV cable just by clamping CT to the conductors in a lump.*Low Cost!:Can measure line/leakage current in the same manner as ordinary clamp meters.
-
product
Cable Tester
KT-200
Test with UTP (Unshielded Twisted Pair) and STP(Shielded Twisted Pair) cable. Check continuity and configuration of wiring with unshield and shielded modular plugs. Test for open circuits, shorts, miswires, reversals, and split pairs. SHIELD detection tests a cable's shield integrity. Test T568A,T568B ,!0 Base-T and Token Ring configurations. Special switch for select symmetric configurations or Non-symmetric cable use for connecting 2 PC.
-
product
Shield
Arduino Ethernet Shield 2
The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino Boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you! *Requires an Arduino Board (not included)
-
product
VLF/DC Hipots
HVA28TD
The smallest VLF /DC unit on the market now includes an integrated Tan Delta measurement system to perform advanced electrical insulation diagnostics. For example, this can be extremely useful when performing advanced diagnostics on cable systems as it provides valuable information as to the condition of the cable insulation and shield.
-
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 20 GHzVSWR 1.15 + .01 (f) GHz w/ RG142 (8 GHz)1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG 223 Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Mini Coax, Contact, ITA, RG316 Double Shield
610103152
Mini Coax, Contact, ITA, RG316 Double Shield.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
Twinax Contacts
VPC twinax contacts provide differential voltage options most commonly used in digital and data applications.For increased reliability and to eliminate the need for polarization, the design of VPC's twinax contact consists of two concentric inner conductors for termination to the twisted pair, and an outer shield for termination of the cable shield.
-
product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, 80 Twisted Pairs, Shielded Multifunction Cable, 1m
192061-01
The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths. 80 twisted pairs, 1 connection used in shield. 81 total connections used.
-
product
Coax, Contact, Receiver, 75 Ohm HD, sm59/U Belden 1855A, 3 GHz
610102133
Primary mating contact 610102132. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – BrassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 2.0 lbs max [0.91 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR ≤ 2.26 @ 3 GHzInsertion Loss -0.86 dB MaxDWV 1500 VDC min.Contact Resistance 5 mΩ center/ 3 mΩ outer Cable Specifications sm59/U Belden 1855AEnvironmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition EInsulation Resistance 1000 MΩ min.
-
product
Shield
Arduino MKR ETH Shield
You may want to connect an Arduino MKR board with an Ethernet cable instead of using WiFi. An Ethernet connection can sometimes be stabler, faster, and more secure. To do this, plug in the Arduino MKR ETH shield.
-
product
Mini Coaxial Contact, Receiver, RG316 Double Shield
610104149
Mini Coaxial Contact, Receiver, RG316 Double Shield.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
DataComm & LAN Testers
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
product
78 Ohm Twinax Cable
RG108A/U
RG108A/U part number from Pasternack is a RG108 twinax cable that is flexible. Pasternack RG108 flexible twinax cable is 78 Ohm and has a PE dielectric. Our RG108 twinax is constructed with a 0.235 jacket made of PVC. RG108 twinax has a shield count of 1 and the maximum frequency for this Pasternack cable is 1 GHz. RG108 twinax cable has an attenuation at 1 GHz of 34.6 dB and a maximum power of 30 watts at 1 GHz.
-
product
EMI Filtering Analyzer
RS Analyst™
With RS Analyst circuits can be analyzed prior to fabrication to determine whether radiated susceptibility requirements will be satisfied. RS Analyst is ideally suited for predicting the effectiveness of EMI filtering for power line and signal line filters and for determining the effects of cable shielding and shield terminations.
-
product
Cable Tester
KT-468
Test device used UTP and STP network wiring and phone line. Check continuity and configuration of wiring with unshielded and shielded modular plugs. Test for open circuits,shorts,miswires and reversals. SHIELD detection tests a cable`s shield integrity. Main unit and one remote allow one person testing
-
product
SparkFun Spectral Sensor Breakout
AS7262 Visible (Qwiic)
The SparkFun AS7262 Visible Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7262 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic Shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
product
LAN Tester
RJ45
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
LANTRACKER
PH-100/120
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
-
product
Twinax, Contact, Receiver, 50 Ohms
610113144
For increased reliability and to eliminate the need for polarization, the design of VPC’s Twinax contact consists of two concentric inner conductors for termination to a twisted pair, and an outer shield for termination of the cable shield.
-
product
93 Ohm Coax Cable
RG62A/U
RG62A/U part number from Pasternack is a RG62 coax cable that is flexible. Pasternack RG62 flexible coax cable is 93 Ohm and has a PE (AS) dielectric. Our RG62 coax is constructed with a 0.239 jacket made of PVC. RG62 coax has a shield count of 1, a RF shielding of 45 dB and the maximum frequency for this Pasternack cable is 1 GHz. RG62 coax cable has an attenuation at 1 GHz of 8.7 dB and a maximum power of 77 watts at 1 GHz.
-
product
Phase Stable Cable Assemblies
Phase Master
Superior phase stability vs. temperature makes this cable the ideal choice for phase-sensitive applications— particularly those with wide operating temperature ranges.Phase Master's enhanced phase stability— a result of a proprietary combination of high performance, tape wrapped PTFE dielectric and helically wrapped SPC shield—offers:- Improved system performance- Less frequent calibration- More precise measurementsFrom environmental stress screening to electronically scanned radar systems, count on Phase Master® assemblies to provide unparalleled value and performance.
-
product
Coax, Contact, ITA, 75 Ohm HD, sm59/U Belden 1855A, 3 GHz
610102132
Primary mating contact 610102133. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter contact – BeCuContact Plating Center conductor shield –30µ” Au over 100µ” NiContact Termination Center conductor - SolderShield - CrimpInsulator PTFEMating Force 2.0 lbs max [0.91 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR ≤ 2.26 @ 3 GHzInsertion Loss -0.86 dB MaxDWV 800 VDC min.Contact Resistance 5 mΩ center/ 3 mΩ outer Cable Specifications sm59/U Belden 1855AEnvironmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Plug'N Check
PH-320/300
The plug‵N′check is our easiest-to use cable tester yet. Simply plug in both ends of a cable, and the easy-to-read LED display explains the cable type and checks whether cable is faulty or good automatically. A shield LED shows results of the shielding check and battery low indicator saves you from misreading the tester in case of low power. Will make work shorter and easier for the layman and the professional alike. Especially suited for installation and maintenance of residential networks.
-
product
Cable Test Box
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
-
product
Qwiic Connect System
An ecosystem of I2C sensors, actuators, shields, and cables that make prototyping faster and less prone to error.
