Filter Results By:
Products
Applications
Manufacturers
AC Sources
Waveform of an Alternating Current circuit is typically a perfect sine wave cycling up and down.
See Also: Programmable AC Sources
- Applied Instruments, Inc.
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Programmable AC Power Source
LSX Series
The LSX Series consists of a range of fully featured, single and three phase AC Power Sources. Available models range from 1.5kVA to 6kVA with an advanced programmable controller sporting a color touch screen user interface. Cost effective and fully programmable for both basic frequency conversion as well as advanced AC power line disturbance test and ATE applications. For applications not requiring advanced features, a basic function set M version of the LSX is available as well.Note: The LMX Series is not CE marked yet at this time.
-
product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
32 Channel Optically Isolated Digital Card
104-IDIO-16 Family
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz. Optically isolating the digital inputs from each other, and from the computer, assures smooth, error-free data transmission in noisy, real-world environments. The 16 input channels are available via a 34-pin IDC type header. The fully protected solid state outputs, capable of sourcing 2A each, are inherently more reliable than electromechanical relays and give system architects a more robust product to design with. The solid state outputs are available via a 50 pin IDC type header.
-
product
Digital kV Meter
VM-10, VM-20 , VM-30
UDEYRAJ ELECTRICALS PRIVATE LIMITED
High Voltage Meters measure AC and DC voltages of up to 30kV with high accuracy. The meter input impedance is as high as 1000 M ohm, making the meter suitable for measurement of voltages of high source impedance circuits. Meters are compact and light weight and can be conveniently used as a calibration meter.
-
product
Basic AC Power Source, 500 VA, 310 V, 2.5 A
AC6801B
Easily access setup and measurement information This basic AC power source offers stable, reliable power up to 500 VA. An intuitive user interface and flexible I/O connectivity.Increase your uptime with stable, reliable AC power sourceEngineer reliability into your designs with a basic AC power sourceTest your designs with confidenceTest under real-world conditions - fluctuating voltage or transient spikes
-
product
High Power Programmable AC Source with Transients
61510
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
product
Multi - Purpose Digital High Voltage Phasing Meter
Model KM-MPS-50K
Kusam Electrical Industries Limited
• AC 50kV and DC 50kV measurement with direct reading.• 4000-count LCD.• Input impedance : 400 Mohm• Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV, DC : 4.000kV / 40.00kV / 50.0kV• KM 50K must be connected with an approved hot stick (Optional).• Check phases are "in-phase" or "out of phase".• Polarity indication : Positive / Negative• Backlight function.• Auto power off.• Power source : 1.5V(AA) alkaline battery × 2.• Low battery indication(Multi-level).
-
product
Manual Oscillators
MOS-01, -01A
The MOS-01 manual oscillator module is used as a quality, general-purpose sinewave oscillator and digital readout monitoring system in the MAC-01, -02, or -03 AC Power Sources/Frequency Converters. The unit has guaranteed operating range of 20 HZ to 20 KHZ which is covered in three one-decade scales. The LCD digital metering system is switch-selectable to readout either frequency, voltage or current. A toggle switch selects the input for the attached AC Power Source/Frequency Converter to originate from the manual oscillator itself or from an external laboratory or programmable oscillator source. With oscillator mode switch in Internal position, the BNC connector delivers the signal to drive additional slave units or for oscilloscope sync or monitoring. BNC input/output is completely isolated with 1500 VAC breakdown and excellent common mode rejection. The oscillator modules must be factory installed and calibrated.
-
product
Charger / Quick Charger / Adapter / LED Driver Test System
6010
6010 Charger / Quick Charger / Adapter / LED Driver Test System is able to meet multi-types power products test requirements，and its multi-U.U.T test simultaneously capability can significantly enhance the production line throughput. It also possess multi-modular combination that includes low noise analog AC source with Triac to simulate output, four sets precision power meter, two or four sets ripple noise / timing measurement module, four sets OVP DC power supply, 3310F series & 3332F/3336F Electronic Load module and unique design 3340F series for LED power driver output test.
-
product
Low Power Programmable AC Power Source With Transients
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
product
AC Source
AMF
The Intepro AMF Series is a complete line of single and three phase, 400Hz AC Frequency Converter products. With Power levels ranging from 6kVA up to 300kVA, the AMF series of frequency converter products are the ideal and cost effective solutions for precise frequency conversion in all avionics and higher frequency electronic applications. Power and frequency conversion is supplied by state-of-the-art IGBT pulse-width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance with minimum downtime.
-
product
DC Power / Energy Absorber Test System
AMETEK Programmable Power, Inc.
The Energy Absorber Test System includes power supplies and a regenerative energy absorber with a rating of 400VDC at ±150A. The system consists of DC power supplies, an AC distribution and interlock system, an energy absorber chassis and an absorber load resistor chassis. The power sources are equipped with a remote control option allowing control via GPIB or with front panel controls in local mode. The operation of the specific parts of the system is described in the sections below.
-
product
RR Signal Source
Behlman’s RR series of Railroad Signal Sources and Frequency Converters are low cost, highly reliable, switch mode units built for Railroad Signaling. The RR series can be supplied with any single or three-phase input and outputs a clean, regulated AC signal at a precise frequency from 25 Hz to 250 Hz. These rugged signal sources are built to support the rigors of operating in the harsh environment of Railroad signaling equipment.
-
product
High Performance Programmable AC Power Supply
IT-M7700 Series
ITECH newly-launched IT-M7700 High Performance Programmable AC Power Supply combines intelligence and flexibility, breaks through the huge defects of the traditional AC power source, reduces the size to only 1⁄2 1U, maximizes space utilization. Built-in power meter and arbitrary waveform generator make it convenient to simulate various arbitrary waveform outputs. IT-M7700 is designed with advanced technologies of programmable AC and DC power supplies, and can be widely used in multiple fields such as power energy products, home appliances, industrial electronics, avionics, military and IEC standards testing.
-
product
USB PD Test System
6050
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
product
Login Digital Epstein Tester Model
Model EP400
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
product
Three-Phase Relay Test Equipment
AK-30
AC voltage source with 4 channels, current source and aux with 6 channels. DC source can be used simultaneously. Amplitude, frequency and phase angle can be adjusted respectively, independently and continuously; Control via PC via Ethernet RJ45 interface
-
product
Filtered AC Interface Module
AC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of AC power.
-
product
AC Source
AFV-P
Intepro’s AFV-P Series is a programmable AC/DC output power source with precision measurement and control. This compact power source comes in four power levels, 600VA, 1250VA, 2500VA and 5000VA, providing clean power with distortion less than 0.3% at 40-100Hz. The AFV-P series delivers output voltage from 0 to 310VAC and frequency from 40 to 500Hz or 15 to 1000Hz with the high frequency option. It is ideal for commercial, defense and aerospace test applications from design verification, quality assurance, ATEs. The AFV-P Graphical Users Interface software makes it easy to setup complex testing of the AC input to the UUT.
-
product
AC Power Sources
i-iX Series II
AMETEK Programmable Power, Inc.
The iX Series II represents a new generation of AC and DC power source that addresses increasing demands on test equipment to perform more functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the iX Series II systems are capable of handling complex applications that have traditionally required multiple instruments.
-
product
AC to AC Programmable Power Sources
AFV-P Series
Rating:600 VA to 5 KVASingle Phase OutputOutput frequency: 45 Hz to 500 Hz (Optional for 15 Hz to 1000 Hz)
-
product
Three-Phase AC Power Source 320 Vrms, 6 KVA, 5000 Hz
AC6906H
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
product
AC Power Sources, Frequency Converter
MAC-01, -02, -03
For reliability, all models of the Titan AC Power Sources/Frequency Converters are fully current limit protected against either continuous or transient short circuit or overload conditions. When an overcurrent condition exists, the internal current control loop overrides the voltage control loop and scales back the sinewave drive until it sees a safe output current level.
-
product
AC Source
AFV
The AFV Series is a broad line of programmable three phase AC power sources. With Power levels ranging from 15kVA up to 2MVA, the series powerful FPGA+ARM based controller offers precise voltage and frequency conversion with power disturbance generation capability. Power is supplied by state-of-the-art IBGT pulse-width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance.
-
product
Safety Voltage Detector
305 SVD
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● AC voltage detection: 100Vac ~ 69kVac ● Frequency range: 40 ~70Hz ● Easy-to-prove method● Self-test function● Power source: 9V alkaline battery ● Non-contact detection by proximity● Convenient to use● Operating temperature and humidity: 0°C~40°C / 80% RH Max.● Lightweight, robust and compact● Easy access to battery● Comply with EN 61326-1
-
product
HIGH FREQUENCY DC BIAS
6565 SERIES
The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.
-
product
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
product
Multiple Output Bidirectional PSU
LAB-MOBI
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
product
AC and DC Current Sources
Programmable AC and DC current sources that provide precise, low noise, stable currents for a number of applications.
-
product
AC Power Source
NF’s AC power sources are designed and built to deliver high-quality, high–precision AC power. In recent years, NF’s products have been used for power-supply environment testing such as immunity testing of electronic components.
