Filter Results By:
Products
Applications
Manufacturers
Automatic Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance. AKA: ATE
See Also: Automatic Test Systems, ATE
- Pickering Interfaces Inc.
product
PXI Very High Density MUX 5 Chan 32 Pole
40-675-002-5/32
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
Power Supply Test System
The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.
-
product
PXI High Density Multiplexer, 8-Bank, 8-Channel, 1-Pole
40-610A-009
The 40-610A-009 is a 8-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Coax Switches
With up to DC - 53GHz bandwidth, low insertion loss, high isolation, and high repeatability, these switches are used to support SATCOM, aviation, military and commercial telecommunications, medical imaging, and ATE systems.
-
product
RF/Switching
SMX-6XXX (RF/Switching)
The VTI SMX-6xxx Series of high density non-blocking RF multiplexers deliver exceptional performance and reliability in a compact single-slot configuration. Front panel connectivity is available in both SMB and PKZ formats to integrate seamlessly into new or existing test systems. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers.The SMX-6xxx Series delivers unmatched bandwidth and isolation performance resulting in exceptional measurement integrity that is ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
product
PXI Very High Density Multiplexer, 49-Channel 2pole
40-670C-021-49/2
The 40-670C-021-49/2 is a 49-channel, 2-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
8/16-CH 16-Bit Analog Output Cards
PCI-6208/6216 Series
ADLINK PCI-6208/6216 series are 8 or 16-CH, 16-bit, analog output cards. The PCI-6208V-GL offers 8 voltage outputs with ±10 V range, featuring 15-bit monotonicity and 10 V/μs slew rate. The on-board analog switches minimize the power-on glitches. PCI-6216V expands the voltage output channels to a total of 16 for higher analog output density requirements. In addition to the voltage output functions, the PCI-6208A features 8 current outputs with ranges of 0-20 mA, 4-20 mA, and 5-25 mA. The daughter board EXP-8A provides high-quality voltage to current transducers. The PCI-6208A device is capable of delivering 14-bit monotonicity with 1.3 mA/μs slew rate. ADLINK PCI-6208 series devices provide high-resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
product
PXI Very High Density Multiplexer, 5-Channel, 32-pole
40-670C-022-5/32
The 40-670C-022-5/32 is a 5-channel, 32-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
Bench Mounted Tester
Flex 10
The Flex 10 bench mounted ATE is the smallest ‘standard’ tester in our range. The system comprises a single unit, measuring 600mm x 360mm x 660mm. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
product
PXI 8 Slot BRIC Solid State 352x8 1-Pole (11 sub-cards)
40-563A-121-352X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 12x4 Matrix, 2 Pole Switching
40-510-022
The 40-510 series of matrix modules feature a wide range of selectable switchingconfigurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signalrouting in ATE and data acquisition systems.Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Larger matrices may be constructedby Daisy Chaining the common signals from multiple PXI modules.
-
product
PXI Very High Density Multiplexer, 5-Channel, 32-Pole
40-675A-002-5/32
The 40-675A-002-5/32 is a 5-channel, 32-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
PXI High Density Multiplexer, 5-Bank, 32-Channel, 1-Pole
40-615A-005
The 40-615A-005 is a 5-bank, 32-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
Dual 16x8 1-Pole High-Density PXI Matrix Module
40-520-205
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Advanced Power System - DC Power Supply, 9 V, 200 A, 2000 W
N6970A
The N6970A is designed for automated test equipment (ATE) applications where high performance is critical.
-
product
Advanced Power System - DC Power Supply, 80 V, 25 A, 2000 W
N6974A
The N6974A is designed for automated test equipment (ATE) applications where high performance is critical.
-
product
High Performance Chipscale Test Sockets
SC
Ardent Concepts Test Sockets for ATE test deploy patented SC Contact Sets. This technology is capable of over 2 Million mechanical insertions in production environments and uses easy to replace pins with no complicated assembly procedure. It is designed to be drop-in compatible with 1mm offset and straight through footprints to ease implementation, and RC SC’s simple and robust design is extremely cost effective when compared with existing “roll” type test contactors and sockets. Designed specifically for JEDEC QFN and MLF applications, SC High Performance Test Sockets are available for most handler set-ups and offer exceptional AC performance.
-
product
PXI 8 Slot BRIC Solid State 96x8 1-Pole (3 sub-cards)
40-563A-121-96X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 2 Amp Multiplexer, Single 16-Channel, 4-Pole
40-635A-003
The 40-635A-003 is a single 16-channel, 4-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Obsolete ATE, Replacement Systems
No one likes saying goodbye to a faithful old friend but now that the economy is on the up, has the time finally come to replace your ageing Automatic Test Equipment (ATE) or Special to Type test system?
-
product
Test Executive & Development Studio
ATEasy
ATEasy is a test executive and a rapid application development framework for functional test, ATE, data acquisition, process control, and instrumentation systems. ATEasy provides all the necessary tools to develop, deploy and maintain software components - including instrument drivers, test programs, and user interfaces, as well as a complete and customizable test executive. It is designed to support and simplify ATE system applications with long product life cycles. With ATEasy, test applications are faster to generate and easier to maintain.
-
product
PXI Dual 10x4 Matrix 2A 1 Pole
40-546-001
Model 40-546-001 is a high density dual 1-pole 10x4 power matrix module. It is also available in single 10x4, single 10x8 or single 20x4 relay formats: Typical applications include power routing in Functional ATE systems, specifically automotive electronics, for example testing of Engine Management Units.
-
product
PXI 8 Slot BRIC 150x8 2-pole (5 sub-cards)
40-561A-122-150X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 24x4 Matrix, 1 Pole Switching
40-513-021
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
product
PXI High Density Multiplexer, 1-Bank, 64-Channel, 1-Pole, Screened
40-610A-016
The 40-610A-016 is a screened 64-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Modular Power
RFP Controller
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
PXI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
40-635A-106
The 40-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Multi-Purpose RF Test System
SPA441
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
product
PXI/PXIe Very High Density Multiplexer, 24-Channel, 8-Pole
40-675B-002-24/8
The 40-675B-002-24/8 (PXI) and the 42-675B-002-24/8 (PXIe) are 24-channel, 8-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
product
10-CH Pneumatics CAN
YAV90PNE
The YAV90PNE is a complete “plug & play” pneumatics subsystem controlled by CAN, for ATEs with Virginia Panel receiver. Thanks to this module, pneumatics actuators that are commonly used in the fixture side of an ATE, can be controlled. 10 3-way micro-valves are able to contorl 10 simple effect actuators or else 5 double effect ones. The module includes input for the position sensors. A pressure sensor is also included, so that the system air mains working pressure can be set between a minimum and a maximum.
-
product
PXI 8 Slot BRIC 30x16 2-pole (2 sub-cards)
40-561A-122-30X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
