Filter Results By:
Products
Applications
Manufacturers
Analogue
representation of a signal that varies over an infinite range of values.
- Pickering Interfaces Inc.
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
Analogue IC Tester
SYSTEM 8 (AICT)
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
Chuan Sheng Electronics Co., Ltd.
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
product
HTOL RF Testing Systems
Becker Nachrichtentechnik GmbH
Fully Automatic Test Systems for Lifetime Simulations of Electronic Components. Each output offers a separate, analogue level control. This ensures highest precision in level during a long term usage. A graphical user interface enables an intuitive and easy control.
-
product
Hand Tools
Moore & Wright have been producing high quality, affordable hand tools for over 100 years to suit many workshop needs from 0-25mm analogue external micrometers to larger, digital versions with USB output.We have also welcomed the brand new Bowers DigiMic into the range, a powerful and efficient Bluetooth external micrometer that is designed to make measurement taking quick and easy, even in the harshest environments.
-
product
Barometers
These barometers can be found in the section to measure absolute pressure, differential pressure in respect to the atmosphere and negative pressure. There are barometers such as the DB2 digital barometers that have an internal memory for up to 750 Barometers to measure absolute pressure, differential pressure in respect to the atmosphere and negative pressure. readings and an analogue output of 0 to 1 volts. These barometers are perfect to measure atmospheric pressure, also called barometric pressure, is an expression for the weight of air (atmosphere) due to the earth''s gravitational pull. This pressure at sea level is 1013.25 mbars (milibars).
-
product
VVK AXIe Switch
VVK AXIe MODULE
Based on the VVK AXIe module, up to 1500 channels of the TEST-9110-AXIe cable tester can be placed in a 6-slot AXIe crate, 3900 channels can be easily placed in a 14-slot crate, which in terms of channel density is a record among analogues on the Russian market.
-
product
Time Controller
ID900
IDQ’s Time Controller is an all-in-one device designed for flexibility and it efficiently solves a large number of problems encountered in the laboratory. Its core consists of 4 high-speed (<20 ps precision, 100Mcps rate) inputs and 4 high-speed outputs, interconnected by reconfigurable logic. The Time Controller performs the functions of a number of devices: time-to-digital converter, coincidence counter, delay generator, pattern generator, counter and discriminator. This is complemented by a 10Gbps link to the host computer for fast data transfers, by auxiliary analogue and digital I/O for interfacing with external devices.
-
product
HIGH VOLTAGE MEGOHMMETER
MI-20KVe
The MI-20KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 4.000.000 MΩ with four test voltages: 5 kV - 10 kV - 15 kV and 20 kV. Readings are performed through an easy-to-read analogue indicator, having a broad scale.
-
product
Surface Roughness Meters
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
product
Lock-In Amplifiers
Anfatec's lockin amplifiers use a unique DSP technology which is only found in these instruments. High speed real-time data processing is combined with optimized analogue input stages. Fully digitally designed high quality filtering ensures an excellent suppression of background signals and an unsurpassed dynamic reserve.
-
product
Signal Transporter E/O - O/E Converter pair
LTX-5515
The LTX-5515 enables the precise conveyance of one analog channel plus four digital channels of information over fibre optic links ranging from metres to more than 10 kilometres. Incoming analogue data is digitised to 12-bit precision at 100 megasamples per second and transmitted over optical fiber at one giga-bit per second.?
-
product
Digital Colorimeter & Illuminance Meter
CHC-I
This Digital Color Meter & Illuminance Meter is based on all digital integral photometric and colorimetric measurement technology. It has no analogue unit, thus it is very simple to overcome the zero drift which is impossible to be avoided in current colorimeter. The digital X (λ), Y (λ), Z (λ) sensor has large dynamic range so that there is no range-changing error in it; moreover, it possesses strong anti-interference ability and high accuracy. The CHC-I contains internal RS232 computer interface, the calibration is done by software. It is suitable for monitoring and remote applications. The CHC-I software can calibrate the instrumentation, sample the data through RS232 interface and print out the results. It can also be calibrated by other standard light sources to obtain very high measuring accuracy of x, y color coordinate and color temperature. It is a real-time measuring system and run under Windows System. 128*64 lattice LCD display, RS232 computer interface and software, Data hold function.
-
product
5 Digit Preset Counter
CS2-CT
Chuan Sheng Electronics Co., Ltd.
The CS2-CT provides high speed and multifunction, counting, control and communication (Modbus RTU mode) of Pulse from flow meter or encoder, proximity switch, photo switch for length control.There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue,and RS485 port available. They are also support N, R, C mode for totalizer control.
-
product
Analogue Concrete Test Hammer
181
The Elcometer 181 Analogue Concrete Test Hammer provides a quick, simple and inexpensive method for non-destructive evaluation of concrete compression strength and other masonry materials.
-
product
DIGITAL MULTIMETER, MEAN VALUE, 10A, 1KV
72-13580
*Digital multimeter with 6000 counts display*CAT III 1000V, CAT IV 600V safety rating*Manual function select and auto ranging*LCD backlight and 0.1% to 99.9% duty cycle*Data hold, max/min/relative modes*61 segments analogue bar graph*RS232 interface*Input protection*Powered by 9V (6F22) battery*12-month limited warranty *view Terms & Conditions for details
-
product
10 Digit Rate/Batch Counter
CS2-MC
Chuan Sheng Electronics Co., Ltd.
The CS2-MC provides dual input(A/B phase) and display with high speed, counting, control and communication (Modbus RTU mode) of Pulse from encoder, proximity switch, photo switch or flow meter for counting, length and position control. There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, and RS485 port available.The relays are also support N, C, R, E mode and Hi/Lo energized for batch / totalizer and position control.
-
product
Bench/System Linear Regulated DC Power Supply With Smart Analog Controls, Single, Dual Or Triple Outputs, 48 To 242 Watts, With/without Remote Interfaces
PL Series
ingle, dual or triple output modelsModels from 6V/8A up to 60V/1.5ALinear regulation - for the best performanceUltra-compact design - uses up less spaceTrue Analogue controls - for ease of useS-Lock function - instantly lock settingsV-Span function - customize the voltage rangeLow current range and current meter averagingDC output switches and "view limits" buttonSelectable remote sense terminalsIndependent, Isolated Tracking, Ratio Tracking and True Parallel modes on dual & triple modelsHigh current low voltage output on triple output model
-
product
Pyranometer products
Hukseflux Thermal Sensors B.V.
Hukseflux is a leading manufacturer, both in technology and market share, of pyranometers, pyrheliometers, pyrgeometers, net radiometers and albedometers.We produce a complete range of solar and longwave radiation sensors, compliant with the latest ISO, IEC and WMO standards. Each Hukseflux pyranometer is classified as ISO 9060 secondary standard, first class, or second class, and offers the best measurement accuracy in its class. Pyranometer output is analogue and/or digital (Modbus over RS-485/TTL).
-
product
Advanced Type ITU Wavelength Adjustable Externally Modulated Optic Transmitter
HT8500T
Hangzhou Huatai Optic Tech. Co., Ltd.
RFTV is a unidirectional analogue and digital video broadcast. It adopts high efficiency modulation mode for RF carrier wave and its economical efficiency, flexibility and bandwidth validity is beyond comparison of IPTV. By adopting EPON, GEPON or P2P access mode to realize triple-play and FTTx, RFTV broadcasting network in 1550nm optical wavelength still plays an important role and 1550nm externally modulated optic transmitter is the core equipment in this system.
-
product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x-DS
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
product
VU Meters
Hoyt Electrical Instrument Works Inc.
The Retro Audio Level analogue panel meters complement the proven and popular Presentor series. The meters offer a performance not significantly different from full specification vu meters to meet today's specific audio market requirement for both quality and distinctive 'retro' styling at an affordable price.
-
product
E/O Converter
LTX-510
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
-
product
Microwave Wideband PIN-TIA Receivers
MR22 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR22 series microwave wideband optical receiver, adopts High linear PIN diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
47~2600MHz Digital TV & Satellite TV PIN Optical Receiver
HRS-26D/P
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26D/P optical receiver, adopting high-sensitivity PIN detector, receiving sensitivity is -22dBm, typical value -13dBm. It can receive analogue and digital signal with the frequency of 47~2600MHz on a single fiber, and compatible with any FTTx PON to achieve triple-network combination between Analog TV(<10CH), Digital TV (DVB-C, DVB-T), Satellite TV (DVB-S) and Internet & FTTH.
-
product
Multifunctional Meter
CPM-10
Chuan Sheng Electronics Co., Ltd.
CPM-10 Multifunction Power meter measure single phase 2 wire ,single phase 3 wire, three phase 3 Wire and 3 Phase 4 wire systems with high accuracy measurement for parameters such as voltage, current ,active power, reactive power, apparent power, power factor ,frequency, effective energy (V,A,W,Watt-Hr,Var,Var-Hr,VA,PF,Hz), having LED display and standard communication RTU Modbus RS485..Optional functions 1 set relay output,1 analogue,1 RS485 (ModbusRTU Mode) or 1 pulse output. Most suitable for power management,remote input /output, alarm and remote signal control uses needs.Case depth 120mm only, easy panel mounting installation
-
product
Analogue+Digital Multimeter
ST-3502
Standard Electric Works Co., Ltd
● 3½ digit, high contrast LCD, with a maximum display of 1999● Automatic polarity indication, zero adjustment● Low battery (BAT) indication● Over range indication: highest digit of (1) or (-1)● EN 61010-1 CAT III 600V, EN 61326-1
-
product
Analogue Oscilloscope
Is a device used to measure voltage against time in an electronic instrument. ... The simplest and earliest type of oscilloscope comprises of a vertical amplifier, a cathode ray tube (CRT), a timebase, a power supply and a horizontal amplifier.
-
product
Digital Panel Meter
MWH-10A
Chuan Sheng Electronics Co., Ltd.
MWH-10A Energy Meter offers high accuracy measurements of Energy (Watt-Hr) and Active Power, display and communication functions. It is also with 1 relay output, 1 analogue output, 1 RS485 communication port, and 1 pulse output in option as well 112mm (D) is ideal for assembling in panels with limited penetration depth.
