Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector
40-153-104
The 40/42-153-104 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Relay And Protection Testing
As the first protection relay test set manufacturer in China, PONOVO has been always offering reliable protection relay testing equipment for customer for more than 20 years. More than 20,000 relay test kits has been supplied to users in China and other countries, including 6-phase, 3-phase, single phase relay test sets, capable of testing all kinds of protection relays, from electromagnetic relays, solid state, numerical, microcomputer relays and digital relays based on IEC61850 as well as other testings, such as, energy meter, transducer, etc. With various models with different specifications, users can definitely choose the model suitable for their testings.
-
product
RF/Switching
SMX-6XXX (RF/Switching)
The VTI SMX-6xxx Series of high density non-blocking RF multiplexers deliver exceptional performance and reliability in a compact single-slot configuration. Front panel connectivity is available in both SMB and PKZ formats to integrate seamlessly into new or existing test systems. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers.The SMX-6xxx Series delivers unmatched bandwidth and isolation performance resulting in exceptional measurement integrity that is ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
product
PXI-2799, 40 GHz, 50 Ω, Dual SPDT PXI RF Relay Module
782359-01
40 GHz, 50 Ω, Dual SPDT PXI RF Relay Module - The PXI‑2799 is a general-purpose single‑pole double‑throw (SPDT) switch module for routing RF or microwave signals in automated test applications. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2799 is also well-suited for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use its onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
Quasar Smart Relay Tester
The Quasar is the most advanced three-phase relay test set designed for the testing of secondary and IEC-61850 protections of any type with special focus on industrial and routine maintenance applications.
-
product
Advanced Three Phase Automatic Relay Test Sets
MP 3000 Series
Advanced three phase automatic relay test set. PC control through user friendly MPWIN Relay Test Software. High accuracy and high power over wide range. Suitable for IEC61850 GOOSE simulation, subscription and sampled value publishing. CE, FCC.
-
product
Step Up Transformer
MagD
SCOPE proudly introduces Step-Up Transformer - MagD, specially designed to cater the needs of testing of instrument Transformers. Before new systems are put into service or after any occurrence of fault, the instrument transformers need to be tested for their outputs. It is to be ensured that these instrument transformers are giving proper outputs to the protective relays. MagD is used to plot excitation curves for instrument transformers. Inbuilt voltmeter and ammeter, eliminates the need of external meters for plotting of curves. It can also be used for de-magnetization of transformer cores and also turns-ratio tests can be conducted using MagD.
-
product
Diagnostic Test Tools For Switching Systems
You know that verification and diagnosis of complex switching operation in a test system has always been an issue. Two of our latest offerings in diagnostic test tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
product
LXI 75Ω RF Matrix - 1GHz
The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family. It maintains a close path loss match for all routes through the matrix, minimizing the calibration effort that has to be invested by users in optimizing their test system performance. The design is non-blocking Y to X (or X to Y) allowing any input to be connected to any output. The construction is based on high quality electromechanical relays which provide a fast operating time compared to microwave relays.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Automatic Relay Test Set
DRTS 66
DRTS 66 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 6 Current and 6 Voltage generators simultaneously available.
-
product
Software for System-Based Protection Testing
RelaySimTest
RelaySimTest is a software solution for system-based protection testing with OMICRON test equipment that takes a novel, future-oriented approach: the test is independent of relay type and relay manufacturer and the often very extensive parameter settings. Instead, it completely focuses on the correct behavior of the protection system. This is made possible by simulating realistic events in the power system.
-
product
Dual Servo Electrical Test Fixture
TA-334001
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
product
Primary Test Equipment
LET-400-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.The regulation system is based on a continuously variable autotransformer (Variac) that supplies to a power transformer that delivers the high current outputs and isolate the main supply from the load. A built-in ammeter and a timer gives the information about the current value and the operation time of the relay or breaker under test.
-
product
Automatic Voltage Regulating Relay- Standard Model
NMC’s Microcontroller based Automatic Voltage Regulating Relays (AVR Relays) are latest technology based Relays used for regulating the secondary voltage of Power Transformers with On Load Tap Changer (OLTC). The Parameter settings are made through the front panel keys & are stored in NVRAM. Independent time delays can be set for first control pulse & subsequent pulses. Built-in Tap displays Tap number of Power Transformer. OLTC is blocked for UV, OV, OC, CF, Min/Max Tap Positions & Tap Fail . in manual mode, Tap Raise/Lower can be achieved through front keys. In TEST mode, Relays, Display and LED indications can be checked. A pair of contacts are available for Raise, Lower, UV, OV, Manual Mode, CF, TF & OC. There are two nos. of 5 Amps C.T.’s available, one for the Over Current blocking and L.D.C. & other for measuring the Current.
-
product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
product
PXI High Density Multiplexer: 99-ch, 2-Wire, 100Vrms/1A, Armature Relays
M9103A
The M9103A, a high-density, high-power 99-channel multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time, or multiple channels can simultaneously connect if needed. This module is ideal for routing multiple analog signals to a measurement device in an automated test environment (ATE) or data acquisition systems. Each channel switch has a high and low for 2-wire switching. The high-quality armature relays are capable of switching up to 100Vrms, with up to 60W of power. Choose from the durable connector block or standard cable connections.
-
product
PXIe-2746, 2.7 GHz, Quad 4x1 PXI RF Multiplexer Switch Module
780587-46
PXIe, 2.7 GHz, Quad 4x1 PXI RF Multiplexer Switch Module—The PXIe‑2746 is a PXI RF multiplexer switch module that is ideal for switching RF signals up to 2.7 GHz in production test applications. The high channel count of the PXIe‑2746 makes it well-suited for test systems that require switching a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. It also features onboard relay counting for relay monitoring.
-
product
Single Phase Relay Tester
PTE-100-V
The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This technology allows users to test many different specific functions required in relay testing, without the need of additional accessories.
-
product
PXIe-2790, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module
782576-01
PXIe, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module—The PXIe‑2790 can either switch or combine RF signals for multi-DUT cellular and wireless connectivity production test. It features high-performance solid-state relays that offer unique benefits such as an unlimited mechanical lifetime and fast switching time, as well as front-mounted SMA connectors that provide easy connection to your RF devices.
-
product
PXI-2540, 350 MHz, 8x9 PXI RF Matrix Switch Module
778572-40
350 MHz, 8x9 PXI RF Matrix Switch Module—The PXI‑2540 is an RF signal switching matrix. With its non-blocking design, you can simultaneously connect any row or column within the switching matrix and maximize the flexibility of your test system. Isolation relays on the module disconnect unused parts of the switching matrix to maintain RF performance and high isolation. The density and bandwidth of the PXI‑2540 is ideal for routing signals between digitizers, function generators, and other RF generators and analyzers.
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
PXI-2567 , 64-Channel PXI Relay Driver Module
778572-67
64-Channel PXI Relay Driver Module—The PXI‑2567 is an external relay driver that works with internal or external power sources. The PXI‑2567 allows you to control relays when the current and voltage requirements for those relays exceed the capabilities found in existing relay modules or for relays embedded in a test system. The PXI‑2567 includes overcurrent, overvoltage, and flyback protection to ensure long-life operation. The PXI‑2567 can also drive small DC motors or other inductive relay coils.
-
product
Relay Data Emulator™
SUBNET SEL
SUBNET SEL Relay Data Emulator Software can automatically learn a SEL relay’s communication capabilities. SUBNET SELRDE Software can then be directly substituted for the physical SEL relay to safely and reliably commission relay communications. Effortlessly change target and meter data through SUBNET SELRDE Software without the inconvenience or risk of physically jumpering contacts or using expensive and often unavailable test sets to directly inject voltage/current.
-
product
Single Phase Secondary Injection Test Set
T200A
T200A Single Phase Relay Testing Kit is the best universal secondary injection test set for engineers who need to do all single phase relay test and other basic primary testing which may require single phase long-term high current injection.
-
product
Text-Based Way to Connect & Disconnect Relays on ABex Modules
ABex Switching
The ABex Switching features a text-based way to connect and disconnect relays on ABex modules. Alias names for channels could be defined in a DUT specific topology file and then be used for text-based switching. These alias names are also shown in the Konrad System Manager allowing easy debugging of test sequences. The ABex Switching functionality could be either used out of NI Teststand with the provided test steps or via API from other programming languages.- Text-based switch routes- XML based topology for Alias mapping- Switch routes with support for Alias names- Seamless integration into Konrad System Manager
-
product
PXI-2534, 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-34
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2534 is a high-density 8x32 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2534 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Maintenance & Test Equipment
To minimize Life Cycle Cost of products and systems it is important to perform maintenance at exactly the right moment: not too early when the product has enough remaining lifetime and not too late when the lifetime is over. Mors Smitt offers a comprehensive set of maintenance and test equipment for in-service inspection, fault finding, and verification of relay conditions for optimum Life Cycle Cost.
