Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
PXI Dual 0-30VDC Programmable Power Supply
TE3200
The TE3200 is a dual output programmable DC power supply designed for use in PXI/CompactPCI chassis. The TE3200 occupies a single slot and will utilize an external supply of 48VDC (provided). A separate srrew-terminal/power adapter board, p/n TE3202, provides connectivity for two 48VDC power suppies and screw-terminals and jumpers for voltage and sense selection and connection. The TE3202 is included with all retail purchases (not included with OEM purchases).
-
product
Test Clips
Angled Nose allows tight hold on 66 blockUse on 110 block with jumper and bed of nailsUse on larger cables with single piercing nail
-
product
USB Tester 2.0
TLS-0050
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
product
Master Controller
RatMaster
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
product
Analog-to-Digital Converter (A/D) and Counter-Timer Card
AD8-16 (ADA-8)
Model AD8-16 (alternate part number ADA-8) is an economical, multiplexed, eight-bit Analog-to-Digital Converter (A/D) and Counter-Timer card for ISA-bus computers. It accepts up to eight differential or 16 single-ended analog inputs (jumper configured). AD8-16 requires a full-size expansion slot. All connections are made through a standard 50-pin connector. Base I/O address selection is via dip switch.Analog inputs are multiplexed, amplified, held by a sample and hold amplifier, and then digitized by an eight-bit A/D converter. Amplifier gain is selected by software and can differ from channel to channel.
-
product
SparkFun Qwiic EEPROM Breakout
512Kbit
The SparkFun Qwiic EEPROM Breakout is a simple and cost effective option to add some extra storage space to any project. With 512 kilo-bits (or 64 kilo-bytes) of storage, this product is great for any microcontroller that doesn't have any EEPROM storage space, like the SAMD21. You can use the Qwiic EEPROM for storing data like GPS waypoints and other user settings that need to be maintained between sketch uploads. The SparkFun Qwiic EEPROM has three address jumpers, allowing for up to eight EEPROMs on one bus. All communication is enacted exclusively via I2C, utilizing our handy Qwiic system (as the name implies). However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
Digital Display for the Transducers and Transmitters
PS57
The PS57 is a combination power supply and 4 1/2 digit LED display for the P55/P855 family of pressure transducers and transmitters. The PS57 accepts 110 VAC power and provides the required 24 Vdc excitation for the transducer. The transducer signal is received and displayed directly in engineering units with bright 0.56 high red LEDs. The user can re-scale the display and set the decimal point by configuring internal jumpers. The analog output of the transducer, 5 Vdc or 4-20 mA, is available on rear-panel terminals.
-
product
3U OpenVPX High Density Multifunction I/O Board
68CB6
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
product
Mini-Link™ Miniature Jumper
Series ML-100
Mini-Link Miniature Jumpers. Used to jumper from row-to-row or from pin-to-pin. Their miniature size makes it possible to stack one on top of the other. A convenient test probe slot is provided as well. Mini-Links are available from the factory with or without a handle, used for ease of inserting or extracting.
-
product
DIP-ER™ Logic Jumper
Series 115, 116, & 117
DIP-ER Logic Jumper. Reliable, electronically tested solder connections. Protective covers are ultrasonically welded on and provide strain relief for cables. DIP-ER Logic jumper wiring is point to point. Consult factory for other wiring needs.
-
product
6U Compact PCI Multiport Serial Card
CP69002
LinkedHope Intelligent Technologies Co.,Ltd.
CP69002 is designed as 6U Compact PCI Multiport Serial Card. The eight serial ports are in depended and magnetic isolated. The transform mode can be configured as RS232, RS422 and RS485 through the jumpers. The upstream interface is 32 bit 33MHz PCI bus.
-
product
I/O Input/Output Board
VME-4514A
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
product
Deluxe Relay Test Set
60660
Jumpers have tabs for clamping and flat pads to place test leads on. No need to pierce wires or connect multiple jumper wires. Also Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter. Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage. Also provides access for a clamp-on amp meter. Relay Puller Pliers easily remove electrical relays without damage to the relay or electrical box.
-
product
Terminals And Test Points
Today's high tech electronics require space saving, low cost methods for connecting and testing circuitry. Our complete line of Quick Fit terminals, Screw Terminals, Solder Lugs and Test Points and Jumpers are designed to meet the interconnect and testing challenges for electronic and electrical component termination points.
-
product
Jumper Cables For Multiport Configuration Of M937xA PXI VNA
Y1242A
Use Keysight Y1242A Jumper Cables for multiport configuration of the M937xA PXI Vector Network Analyzer (VNA).
-
product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
product
SparkFun Digital Temperature Sensor Breakout
AS6212 (Qwiic)
This SparkFun Qwiic Digital Temperature Sensor Breakout provides a combination of high temperature accuracy with excellent low power consumption using the AS6212 digital temperature sensor from ams AG. The sensor measures temperature data up to ±0.2°C; accuracy over a wide range (-40°C; to +125°C;) and consumes an average of 6µA in normal operation (0.1µA in standby). The AS6212 communicates via I2C and has eight available I2C addresses selected by a pair of solder jumpers on the board. The breakout routes the I2C interface to a pair of Qwiic connectors to work with our plug-and-play Qwiic Ecosystem but also routes the bus and other pins to a standard 0.1"-spaced PTH header for users who prefer a soldered connection.
-
product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
product
SparkFun LED Driver Breakout
LP55231
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is well-suited for variable intensity and color-mixing applications!
-
product
MU Cable Tester System
16814
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
-
product
9 Pin Breakout Interface
VSI-Breakout-9
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Pulse Initialization Demo Board
TMR9112
MultiDimension Technology Co.,Ltd.
The TMR9112 demo board was developed to support evalution of the TMR9112 single-axis sensor. The demo board comes with the fast bipolar current pulsing circuit needed for initialising the TMR9112 sensor, and it can be powered from a USB port or any external 5V power supply. For user convenience, the demo board has an optional on-board timer clock with four selectable frequency settings. The On-board timer clock and frequency output can be enabled using the jumper pins. This demo board is divisable along the dotted line so that the sensor board can be seperated from the pulsing circuit board.
-
product
DIN Backplane
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
product
Multi Trailer Tester Jobber Pack
#TSTPK1
Innovative Products of America
4 vehicle side trailer circuit testers and a three-way adapter.Test 7 flat, 7 round, 6 round and 4/5 pin trailers and receive a 3 way trailer adapter. Troubleshoot tractor trailer circuits Allows bypassing of troubled circuitry while on the road Eliminates guesswork "Winged" grip for easy removal from electrical connectorKit Includes:#7893: 7 Flat (Spade) Pin Trailer Circuit Tester#7865L: 7 Round Pin Circuit Tester (includes one brass jumper)#8000: 3 Way Trailer Adapter (7 flat pin to 6 round pin and 4/5 pin)#7897: 6 Round Pin Trailer Circuit Tester#7866: 4/5 Pin Harness Checker
-
product
Economy Mini-Link™ Miniature Jumper
Series ME-100
Economy Mini-Link Miniature Jumper. Mini-LinkTM miniature jumpers are useful for jumpering .025 [.63] square pins on .100 [2.54] centers. Their miniature size makes it possible to stack one on top of the other.
-
product
Pin-Line™ Vertisocket™
Series 0517
Pin-Line Vertisockets. For mounting components, jumpers, etc., at right angle to PC board. Available 1 to 25 positions; cuttable to any number desired.
-
product
VME Module
ICC-8-xxx
The ICC-8-xxx is the second generation of the ICC-8 board. Enhancements includes true RS-485 communications with jumper configurable I/O by the user. The ICC-8-xxx is a VME based, 8 channel intelligent and versatile solution to serial data communications designs.
-
product
Multifunction Analog I/O Board
104-AIO12-8
*Eight true differential inputs, or eight single-ended inputs optional*Programmable input ranges of: 0-5V, 0-10V, ±5V, ±10V*100KHz sampling rate*On-board pacer clock and counter timers*Four double-buffered analog outputs*Jumper selectable output ranges of: 0-5V, 0-10V, ±5V, ±10V*24 digital I/O lines, type 82C55 with change of state detect on port C, buffers on ports A & B*Flexible configurations to suit your needs
-
product
MPO / MTP® Patch Cords
Multi-fiber jumpers and loopbacks deliver the performance and reliability needed in todays’ demanding high-speed broadband and data networks.
-
product
High Impedance Differential Clock Divider
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
