Filter Results By:
Products
Applications
Manufacturers
I2C
IC serial bus protocol speed grades; standard mode: 0.1 / 0.4, fast mode: 1.0 / 3.4 / 5.0 Mbit/s are maximum ratings. AKA: Inter-Integrated Circuit
See Also: Serial, Serial Communications, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
- Pickering Interfaces Inc.
product
SIMRC - 8-Channel 2-Pole Multiplexer
1020-R-8-2-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Low-power, High-performance FPGA
iCE40 LP/HX
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
product
Multi Protocol Analyzer
LE-3500R
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
product
SparkFun Triple Axis Magnetometer Breakout
MLX90393 (Qwiic)
It's time to start utilizing the superior magnetometer, and what better way than to throw it onto an easy-to-use breakout board? The SparkFun MLX90393 Magnetometer Breakout is a triple-axis magnetic sensor board capable of sensing very small fields, while still behaving as one would expect during saturation in larger fields (like a nearby magnet). The MLX90393 breakout can be used as a compass sensor but also works well as a non-contact controller, a flow meter with a magnetic impeller, or a linear actuator position sensor. To make it even easier to to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
product
SparkFun GPS Breakout
XA1110 (Qwiic)
The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to our Qwiic Connect System. Equipped with the XA1110 GPS module from GTOP, this board utilizes the MediaTek MT3333 chipset, loaded with specialized SparkFun firmware that enables both I2C and serial ports simultaneously. Using I2C means you won’t have to tie up your serial port with GPS, leaving it open to other possibilities.
-
product
Sensor Boards
SensorXplorer™
Each sensor board can be used together with the SensorXplorer board.The SensorXplorer boards acts as a USB to I2C interface between Vishay's freely available software modules and the sensor boards. The sensor boards also have test pins for the I2C interface, allowing you to connect them to your own platform.
-
product
SIMRC - 16-Channel 1-Pole MUX, Screened Reed
1020-R-16-1RF-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, SPI, I2C, 2 LANs And DIO (2-in/1-out)
IFB125
The IFB125 is powered by the low-power Freescale i.MX6UL processor in the ARM® Cortex™-A7 micro architecture. It supports extended operating temperature ranging from -40°C to 70°C, and can withstand vibration up to 5G. Its flexible wide voltage range 9V - 48V DC power input with a lockable terminal block type connector also enhances its reliability in harsh environments. To meet most of Industrial IoT needs, the IFB125 supports multiple communication interfaces for maximum flexibility, including LAN, serial, USB, and digital I/O ports. The Industrial IoT gateway has 256MB onboard memory that features data transfer rates of DDR3-1600, as well as 4GB eMMC flash memory onboard for storage. This embedded IoT gateway platform is equipped with one PCI Express Mini Card slot and one SIM card slot. Additionally, it supports DB9 connectors with both SPI and I2C function as communication protocols to suit for specific applications
-
product
SIMRC - 8 x 4 Matrix 1-Pole
1030-R-8-4-1-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
Alchitry Cu FPGA Development Board (Lattice ICE40 HX)
If you are not needing a lot of power to start your FPGA adventure, or are looking for a more economical option, the Alchitry Cu FPGA Development Board might be the perfect option for you! The Alchitry Cu is a "lighter" FPGA version than the Alchitry Au but still offers something completely unique. FPGAs, or Field-Programmable Gate Arrays, are an advanced development board type for engineers and hobbyists alike to experience the next step in programming with electronics. The Cu truly exemplifies the trend of more affordable and increasingly powerful FPGA boards arriving each year. This board is a fantastic starting point into the world of FPGAs and the heart of your next project. Finally, now that this board is built by SparkFun, we added a Qwiic connector for easy I2C integration!
-
product
Optical tTansceiver Module
QSFP28
Eoptolink Technology Inc., Ltd.
Eoptolink’s EOLQ-851HG-02 QSFP28 SR4 100G Optical transceiver module are designed for use in 100 Gigabit Ethernet links over multimode fiber. They are compliant with the QSFP28 MSA and IEEE 802.3bm 100GBASE-SR4 and CAUI-4. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP28 MSA.
-
product
SparkFun Triple Axis Digital Accelerometer Breakout
ADXL313 (Qwiic)
The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI.
-
product
SparkFun Breakout
HMC6343
The HMC6343 is a fully integrated high end electronic compass module that can compute and give you a heading direction that’s accurate within a couple degrees. It is tilt compensated and is calibrated to handle magnetic distortions. This breakout board allows for easy use of the HMC6343. All that is required is power and I2C connections to a microcontroller so that the module can receive commands and send data back to the user.
-
product
Electrical Interface
QSFP-DD 200G
Eoptolink Technology Inc., Ltd.
QSFP-DD 200G Eoptolink’s EOLD-162HG-E-10-1 QSFP-DD CWDM4, 8x25G Optical transceiver module are designed for use in 200 Gigabit links over 10km singlemode fiber. They are compliant with the QSFP-DD MSA. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP-DD MSA.
-
product
ST VL6180X Time of Flight Sensor
SEN-36001
Highly integrated breakout board for the ST Micro VL6180X Time of Flight (ToF) range finder sensor. This sensor has many uses in the robotics, cell phone and gesture recognition space. It has two programmable GPIO pins, and most importantly, measures absolute distance up to 100mm. The SEN-36001 includes a VL6180X IC centered between two 4-40 sized mounting holes with onboard 2.8V LDO and voltage translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and all IC pins have been broken out to a 0.1" pin header. Example code for the Arduino platform is available below and includes code for both the proximity measurement and ambient light sensing capabilities.
-
product
SparkFun IR Array Breakout
55 Degree FOV, MLX90640 (Qwiic)
It's time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accuracy of ±1.5°C (best case). To make it even easier to get your infrared image, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Module Spectrum
nRF52833 Series
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
product
Proximity, Light, RGB, and Gesture Sensor
APDS9960
Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project with the Adafruit APDS9960 Proximity, Light, RGB and Gesture Sensor. When connected to your microcontroller (running our library code) it can detect simple gestures (left to right, right to left, up to down, down to up are currently supported), return the amount of red, blue, green, and clear light, or return how close an object is to the front of the sensor. This device uses an I2C interface so it's easy to wire up and use.
-
product
Beagle I2C/SPI Protocol Analyzer
TP320121
The versatile Beagle™ I2C/SPI Protocol Analyzer is the ideal tool for the embedded engineer who is developing an I2C, SPI, or MDIO based product. The Beagle analyzer provides a high performance bus monitoring solution in a small, portable package. Perfect for engineers in the field and in the lab.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
Serial Bus Buffers, Extenders, and Accelerators
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
product
SparkFun Micro OLED Breakout
The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s "micro", but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of all, though, is the Micro OLED is easy to control over either an SPI or I2C interface.
-
product
Open Standard Module (OSM)
ROM-2860
Advantech ROM-2860 OSM 1.1 Computer-on-Module is powered by Qualcomm QCS6490/5430 SoC which includes up to Arm v8 Cortex® in combination with Andreo GPU 643 and Andreo VPU 633 graphics engine. It provides PCIe, USB 3.2, Giga Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and eDP, DP, MIPI-DSI display for embedded applications.
-
product
Environment click
Environment click measures temperature, relative humidity, pressure and VOC (Volatile Organic compounds gases). The click carries the BME680 environmental sensor from Bosch. Environment click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI or I2C interface.
-
product
Extension Module
GE-DIO-42
Infinite Industrial Informatics Lt
GE-DIO-42 is a digital I/O, DIN rail mount expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
product
Grid-EYE High Performance Type
Panasonic Industrial Devices Sales Company of America
Panasonic's Grid-EYE® Series High-Performance Type is an 8x8 (64) pixel Infrared Array Sensor. This Sensor offers digital output (I2C) for thermal presence, direction, and temperature values. The built-in lens includes a 60-degree viewing angle. The Grid-EYE Sensor features compact SMD design using MEMS thermopile technology. This Sensor offers several advancements over the original Grid-EYE, including higher accuracy, enhanced resolution, and longer detection distance for true next-generation performance.
-
product
Micsig Smart Oscilloscope
STO1000C/E
Shenzhen Micsig Instruments Co., Ltd.
*Up to 70Mpts memory depth, Zoom into a selected part of the captured waveforms to get more details. *Support serial triggering and decode (I2C, SPI, RS232/UART,CAN, LIN) and Aerospace and defence (MIL-STD 1553, ARINC 429). Two formats to display decoding, text and graphic.
-
product
SparkFun Digital Temperature Sensor Breakout
AS6212 (Qwiic)
This SparkFun Qwiic Digital Temperature Sensor Breakout provides a combination of high temperature accuracy with excellent low power consumption using the AS6212 digital temperature sensor from ams AG. The sensor measures temperature data up to ±0.2°C; accuracy over a wide range (-40°C; to +125°C;) and consumes an average of 6µA in normal operation (0.1µA in standby). The AS6212 communicates via I2C and has eight available I2C addresses selected by a pair of solder jumpers on the board. The breakout routes the I2C interface to a pair of Qwiic connectors to work with our plug-and-play Qwiic Ecosystem but also routes the bus and other pins to a standard 0.1"-spaced PTH header for users who prefer a soldered connection.
-
product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-F
Breakout board for the Sensirion SHT31-DIS-F with a built-in permeable membrane filter. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
