Filter Results By:
Products
Applications
Manufacturers
Unit Under Test
assures a constituent's interoperability in a system.
See Also: UUT, EUT, System Under Test, Device Under Test
- Pickering Interfaces Inc.
product
PXI 10A Fault Insertion Switch 10-Chan 1-Bus
40-199-001
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
product
One Phase Electric Power/Energy Calibrator
MC133
The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.
-
product
2 GHz Dual 1:4 RF Mux, 50 Ohm Module for 34970A/34972A
34905A
The Keysight 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
-
product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
product
Single Board Source/Meter/Switch
SMSU
SMSU Series SourceMeterSwitch Unit (SMSU), introduced by SW Link Ltd, is single-channel voltage/current sourcing, 4X6 switch matrix and measurement instruments. Each Series 100 SMSU instrument tightly integrates highly accurate stable DC power source and a true instrument-grade programmable gain amplifier and 18bits ADC on a 100x100mm PCBs. It can output up to 20V, sub-uA to 1A current to device under test (DUT)
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
PXIe-4140, 4-Channel Source Measure Unit
781742-01
The PXIe-4140 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4140 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
product
Benchtop Automated Functional Test
midUTS
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
product
High & Low Temperature Chamber
Jinan Testing Equipment IE Corporation
It is specially designed for universal testing machine to do tensile test for metallic & non-metallic materials under required temperature condition. It adopts liquid nitrogen as cooling media and electric resistance wire for heating. With large observation window . It consists of chamber body, heating unit, intelligent PID temperature controller, temperature sensor, high & low temperature grips, liquid nitrogen container and rolling carriage bracket. It is widely used in universities, R&D institutes and industrial factories etc.
-
product
ITA, G12x, Front Mount, 18 Module
410104474
The G12x ITA can be used with all G12x Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
product
PXIe SSD Storage Unit
DM-4M.2-3U
The Big River™ DM-4M.2-3U PXI Express storage unit provides up to 3.8TB* of M.2 SSD storage capacity. With a PCIe x8 Gen3 host interface, the DM-4M.2 delivers high-speed data rates for sequential writes of 3.25GB/s** and sequential reads of 3.41GB/s** to PXI Express based systems. The single slot design of the DM-4M.2 increases the availability of valuable chassis space, allows for maximum storage flexibility. The DM-4M.2 complies with PCIe Gen3 protocol standards. The product is commonly used in the industrial control, test and measurement fields. The DM-4M.2 operates under Windows, Linux, Unix, Solaris and VxWorks.
-
product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Automated Bench Test Equipment
The Automated Bench Test Equipment (BTE) provides a combination of automatically sequenced and manually selected electrical or electro-mechcanical stimulation to an electronic or electro-mechanical unit under test. The system simulates the normal and threshold operational ranges of each of the inputs and communication channels of the unit under test.
-
product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
product
Piezo Unit Aging Tester
BK2028/BK2028A
We designed the BK2028 and BK2028A Piezo Unit Aging Testers for you to test your piezo electric vibration units for long term reliability. The BK2028 can test up to 50 units at a time, while the smaller BK2028A tests 20. Both models are easy to set up and can be stacked. They allow you to control the number of tests you you run so that you can run a large number of DUT's under exact conditions and make sure your piezo units will do what you expect them to do for the life of your products.
-
product
Endurance Tester
Premier's Endurance Tester, also known as on-off tester and life tester, is used to perform the life test of the unit. The Endurance Tester, switches on the unit for a set time and then turns it off for a set time. This entire cycle is repeated multiple times, to simulate the behavior of the unit under extended use
-
product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
product
C++ Test Aider
Testwell CTA++
Testwell CTA++ is a tool for unit testing C++ classes, libraries and subsystems. The tool is easy to use and provides very powerful features helping the tester to build the testing environments and running the tests on C++ code. Testwell CTA++ is used for building testing environments, test beds, for the code under test (C++ classes, libraries, subsystems, APIs) and then executing the tests with the test bed.
-
product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
Platforms
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
product
SIGNAL & POWER ISOLATOR
EE301-ISOL
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
product
JTAG/Background Debug Mode Test System PXI Card
NX5300
The NX5300 is a single slot 3U PXI device and interfaces to the unit under test via an On-Chip Debug (OCD) or JTAG port. The NX5300 is a high performance JTAG based background debug mode (BDM) diagnostic system designed for functional test, development, programming and troubleshooting of microprocessor and microcontroller based embedded processor systems.
-
product
Network OTDR
NFO series
The NFO OTDR unit injects the laser pulse into the fiber under test and picks up scattered and reflected optical signals by an avalanche photodiode (APD). The unit accepts remote commands from Internet to control all related timing and data acquisition processes. Maximal three wavelengths are available at the NFO with options on 1310, 1490, 1550, and 1625 nm. NFO also has options on dynamic ranges so users can select the most cost effective units for their demands. Radiantech provides an easy use API (Application Program Interface) for NFO so users can design and build their own AP for NFO. Standard NFO API package is for Windows XP or higher. Please contact Radiantech’s sales person to inquire API for another OS.
-
product
IP X3, X4 - Rain Test Chamber
The rain water or moisture penetrating through a leak in the case, can often reach into the circuit board and lead to failure of the equipment. This problem is frequently encountered with external equipments and devices during storage, usage or transportation in a rainy weather. Therefore, the automotive industries and various research and developmental units often use Rain Test Chambers to test the quality and performance of the product in such extreme environments.Weiber's Rain Test Chambers are such Rain Testing Machines/Chambers used for the testing of automobiles, electronic parts and components, light equipments, voltage cabinets and other wide variety of products under a rainy environment. These IP Test Chamber and IP Testing Chambers are designed to simulate specific environmental conditions, mimicking a natural rainy weather, to test the seals and water proofing capacity of the equipment and devices, thereby providing an estimation of the product performance over a period of time.
-
product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
In-Circuit Tester Integration
The benefits of boundary-scan are noticed in all phases of a product life cycle. By coupling the power of Corelis boundary-scan tools with an In-Circuit Tester (ICT), a complete, integrated solution is available that offers the best advantages of both technologies.Boundary-scan operates as the perfect companion to ICT. Boundary-scan is capable of testing areas of printed circuit board assemblies that are difficult to access due to physical space constraints and loss of physical access, which is often due to fine pitch components such as Ball Grid Array (BGA) devices. Conversely, the ICT is able to check the non-boundary-scan compatible portion of the unit under test (UUT) such as analog.
-
product
SWB-2813, 4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-13
4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2813 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Torque Measuring and Monitoring System
WISER 4000
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
