Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Resistance Temperature Detectors (RTD) Simulators
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
product
Chamber/Pyroelectric Task
Radiant's Chamber/Pyroelectric Task sets the sample to a series of temperatures by performingGPIB control of an external thermal device. At each temperature it captures the sample’s polarization response and/or small-signalcapacitance. These are combined to calculate the pyroelectric coefficient. The Pyroelectric Task is to be used with a Radiant Test System and a Linkam Stage (-196C to 600C), Thermal Chambers, Hot Chucks, or a Furnace to automatically measure the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled. Radiant's Pyroelectric measurement Task can be added to Vision at additional cost. This measurement suite fully characterizes the pyroelectric charge (polarization) response of the sample under test. The Pyroelectric Task suite controls various thermal controllers such as Quantum Design, Lake Shore, Delta Design, and many others. Detailed Listing of Thermal Controllers Registered in Vision. The Chamber/Pyroelectric Task is quoted upon request.
-
product
Vacuum Chuck Temperature Controlled Test Stations
These test stations offer the same reliable repeatable measurement capability of our temperature monitored stations with the added dimension of temperature control.
-
product
On-Wafer Measurements
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
product
Probe Station
ETCP1000
Installation of “Hot and cool chuck” - Sellectable chuck size : 4inch, 6inch. - Temperature variation : -193°C ~ 300°C (80K ~ 573K) - Additional requirements : Vacuum chamber, LN2 tank(Bombei), microscope, CCD camera, manipulators. - EPS500 is standard model in ETCP1000 probe station.
-
product
Thermal Chuck Systems
A-Series
Advanced Temperature Test Systems GmbH
The A-Series represents a productline of air cooled thermal chuck systems for a temperature range between -30C up to +400C. The basic product offers an active cooled chuck system without an external chiller for a temperature range between +25C up to +200C at a very competitive price to common Hot Chucks.
-
product
Pyroelectric and Thermal Testing
The optional Chamber Task measures the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled within a thermal chamber, on a hot chuck or in a furnace. From these measurements the Spontaneous Polarization Pr(q) and the Dielectric Constant er(q) are computed. These are then combined to determine the Electrical Displacement D(q) as a function of the temperature q.
-
product
Thermal Chuck Systems
C-Series
Advanced Temperature Test Systems GmbH
Looking for a chuck system that gives you the possibility to cool down to - 60C and up to + 300C. The C-Series represents a product line of air cooled thermal chuck systems for a wide temperature range
-
product
Ambient Temperature Vacuum Wafer Chucks
6" (152mm) Vacuum Wafer Chuck for General Purpose Ambient Temperature testing with a Stainless Steel vacuum wafer surface
-
product
Thermal Controlled Chucks & Plates
TOP Cool
Mechanical Devices newest innovation in thermal testing. Each TP system contains a thermal chuck or thermal plate and a self-contained thermal control unit.The TP chuck and platforms is a breakthrough product that introduced the use of refrigerant for active cooling & heating of wafers and other components with no need of chiller, CDA, or consumable and expensive refrigerants such as liquid nitrogen and liquid carbon dioxide. It can be a perfect replacement system in the industry for uncompromising thermal and mechanical performance with a temperature ranging from -60 to +220°C.
-
product
Wafer Chucks
American Probe & Technologies, Inc.
High Performance Chuck for your needs Introducing the American Probe & Technologies’ HC-6000 series of thermal chucks,
-
product
Drill Chuck Grips
Metal rods, wires, and plates and electronic components can be tensile tested using drill chuck grips. Electronic components are tested by placing the metal legs of the components in the grips, allowing different shaped components to be tested with the same set of grips.
-
product
Standard Probe Station Chucks & Accessories
In this test solutions section of our website we describe the expanding line of Abet PV IV probe stations for the growing variety of solar cell types and sizes being developed around the world. This page describes a line of vacuum chucks and accessories for top/bottom, top/top, and bottom/bottom solar cells from 3 x 3 mm to 300 x 300 mm. Probe stations for multiple device on a single substrate and multifunction probe stations are described further in the sections highlighted to the left of this page.
-
product
Electrostatic chucks
Semiconductor substrates such as Si wafers or masks for the next generation of extreme ultraviolet lithography (EUVL) are handled in a vacuum. For nm structures and exact overlay, the reproducibility of the substrate evenness is a crucial factor, as unevenness results in structural distortions. Particles are problematic and heat input as well as thermal expansion must be taken into account.
-
-
product
Temperature Transmitter
T0418
For exacting interiors in building energy management and HVAC systems. Are designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets.
-
product
Temperature Probes
Is a device, typically, a thermocouple or RTD, that provides for temperature measurement through an electrical signal. A thermocouple (T/C) is made from two dissimilar metals that generate electrical voltage in direct proportion to changes in temperature.
-
product
Temperature Controller
8C
The Series 8C Temperature Controller offers easy-to-use programming menus designed for quick installation. The unit is designed for direct or reverse acting (cooling or heating) control. The Series 8C can be programmed for simple ON/OFF or more complex PID control functions.
-
product
Temperature Probes
Used for immersion temperature measurement in liquids, air, gas, or wells in solid material, Omega offers a large variety of probe styles in thermocouple, RTD, thermistor, and IC technologies.
-
product
Temperature Sensors
Robust temperature transducerWith integrated Pt1000 sensorOutput signal 0-10VTemperature range -30 to 80 CPower supply 15-30Vdc / 24VacSupplied with calibration certificate
-
product
Temperature Kit
TEMPKIT
The Power Probe Temperature Kit is designed to give readings for ambient temperature and from the wireless Temperature Probe. The Tempkit has a built–in temperature sensor in the base unit, plus a temperature sensor in the remote wireless Probe. This allows for multiple readings simultaneously. One additional wireless Temperature Probe (TEMPPROBE) is available separately, for a second temperature reading.
-
product
Temperature Test
Function and safety under extreme conditions. In the field of environmental simulation, ENGMATEC offers a wide range of efficient systems for quality assurance, development and production.
-
product
Temperature probes
Industrial platinum resistance thermometers 935 are suitable for use in the laboratory or on site. They can be used as a standard work on an oven or a calibration bath or as a precision sensor for our temperature indicators thermometers.
-
product
Transducers for Temperature
Overview of transducers with Ethernet interface for temperature and humidity.
-
-
product
Temperature Sensors
A device, typically, a thermocouple or RTD, that provides for temperature measurement through an electrical signal.
-
product
Temperature and Pressure
Encore Electronics manufactures a complete line of rugged and economical instrumentation for temperature and pressure measurement. Our standard, in-stock units can be used for pressure measurement depending on the signal level and output required. Our equipment is available in both DIN rail and modular/rack-mounted configurations for multiple channel capability. Simply specify your output — whether 4 to 20mA , 0 to 10V, or a custom output and Encore can configure a system to match your needs. Whether you need isolated input and outputs using transducer power or computer-controlled units, we will design and build a unit to meet your requirement.
-
product
Temperature Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitters for platinum temperature sensors and thermocouples in 6 mm housing with calibrated range selection. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
-
product
Temperature Calibrators
Ensuring process temperature accuracy involves calibrating not only the system’s electronic temperature signals, but also the very temperature sensors that initiate those signals. Rugged Fluke handheld temperature calibrators source and measure RTDs and thermocouples, power transmitters, and store data. Fluke Calibration temperature sources cover temperatures from -45 °C to 1200 °C and include handheld, portable, and benchtop calibrators. Infrared thermometer calibrators and reference measurement thermometers ensure every necessary tool is available to you.
-
product
Temperature Switch
T150D
The T150D Adjustable Stainless Steel Miniature Temperature Switches provide the end-user with a wide range of functionality without impacting durability. The T150 is designed for use up to 510°F but can withstand temperatures up to 800°F while still protecting the set point and life of the switch. The limit filled, saturated vapor sensor is in direct contact with the temperature-sensing outer shell producing fast response and accurate temperature control. The external setting scale provides full range adjustment and the external lock screw allows for easy adjustment of set point.
