Filter Results By:
Products
Applications
Manufacturers
PHY
Tests hardware, electrical and procedural interface to the transmission medium.
-
product
PhyView Analyzer
PVA-3000
Connects up to 24 10/100/1000Base-T ports and provides access to the PHY Performance Test Suite supporting one-click, fully automated transmitter, receiver, and, auto-neg testing.
-
product
CPE Design Verification System
Jupiter 310
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
product
DH Series Tip - CrossSync PHY PCIe5 CEM x16
DH-CSPHY-PCIE5-CEMX16
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
RF PHY Tester
TLF3000
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
product
Ethernet Controller ICs
CP220x
The CP220x family is the industry's smallest single-chip Ethernet controller containing an integrated Media Access Controller (MAC) and Physical Layer (PHY).
-
-
product
Ethernet Transformers
Pulse’s Ethernet transformers are RoHS compliant and qualified at major PHY suppliers. 100/1000/2.5G/5G/10GBASE-T Ethernet transformer modules are optimized for all major LAN transceivers. All modules provide electrical circuit isolation that meets IEEE 802.3, while maintaining signal integrity needed for the most demanding applications.
-
product
SD Card V.4.1 & UHS-II PHY
SD 4.1 Total Solution
To meet the ever increasing data transfer rate in high end applications, such as professional broadcasting transmission or advanced high resolution display, the SD 4.1 specification calls out the maximum performance of 1.56 Gbps at UHS-II full duplex mode per lane or half duplex UHS-II at 3.16 Gbps. In real applications, due to the system overhead and different SD 4.1 device controller designs, the actual measured performance can vary dramatically from system to system. With the newly introduced ADMA 3, the OS driver is now able to issue multiple read or multiple write commands at once, without having to wait for the SD controller to complete one command at a time. Once the SD host controller has collected multiple commands, it will then manage and complete them without intervention from the host software drive. Thus, the UHS-II 1.56 Gbps interface can be more effectively utilized and maximize the system throughput. This feature can be very useful when running multithreaded applications where multiple applications are constantly updating their status or swapping their contents by writing or reading small chunk of data to or from the memory card.
-
product
HDMI Phy and Protocol Aux Channel Analyzer Module
The Teledyne LeCroy quantumdata 980 HDMI Phy & Protocol Aux Channel Analyzer module supports compliance testing of the HDMI DDC bus and HDMI 2.0 CEC testing (partial support only). The module’s CEC compliance tests enable you to identify compliance failures early in the development cycle. The solution is ideal for pre-testing and self-testing (where permitted) your HDMI 2.0 device. The module also supports compliance testing of the HDMI DDC bus voltage and timing parameters in accordance with HDMI 1.4b. Future releases of the module will support functional tests and compliance tests on other HDMI auxiliary channels.
-
product
C/D-PHY CSI-2/DSI Analyzer
Envision X84
is the first combination C-PHY/D-PHY analyzer in single platform. The Envision X84 supports C-PHY/D-PHY and Cameral Serial Interface (CSI-2) and Display Serial Interface (DSI/DSI-2) on a single hardware platform. Envision X84 supports C-PHY version 1.1 and D-PHY 2.1 as well as CSI-2 version 2.1 and DSI version 1.3 and DSI-2 version 1.1. The Envision X84 offers Silicon ad device designers, integrators and validation engineers a complete, robust yet flexible tool to ensure the correct and efficient operation of Camera and Display over C-PHY and D-PHY implementations.
-
product
Core Solutions
Synthesizable 1394 and AS5643 IP Core solutionsPHY, LLLC, PHY & LLC for multiple FPGA families
-
product
EOC Master
EOCM-7102
Hangzhou Softel Optic Co., Ltd.
EOCM-7102 is the outdoor EOC Master of the EOC (Ethernet Over Coaxial) solution. It is in compliant with HomePlug AV standard. The EOCM-7102 have two EOC module. It provide two TV input, two com output and two 10/100/1000M auto-negotiation uplink ports. It offers the high-speed data service to the customer based on the coaxial cable network. The EOC module in the EOCM-7102 is based the Qualcomm AR7410 chipset solution, with high anti jamming capability OFDM technology. The 7.5-65Mhz low frequency band is used for EOC signals. Built in high isolation filter as CATV RF and EOC signal mixer, the EOC signal and CATV signal in 87~862Mhz can running on one cable without interference. The EOC Master can provide high speed data service. The PHY Layer speed is 600Mbps, the MAC Layer throughput is up to 320Mpbs.
-
product
Arasan PHY IP
Arasan PHY’s are readily available and in production with multiple foundries from 16nm to 180nm. Our PHY’s are designed for low power on the most advanced nodes for the mobile market while also targeting the automobile market on specialized nodes where extreme temperature tolerance is required.
-
product
Industrial Ethernet Physical Layer Devices
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
product
IO-Link
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and communications interface, as well as the IO-Link transceivers featuring Integrated Step-Down Regulators and LDO with ±60V cable interface protection provide the required ruggedness. Optimum EMC performance is achieved with adjustable current limit and slew rate transmitters. Automatic wake-up request (WURQ) generation and an output supply current boosting capability for device startup are also available. Additional components integrate a 300 mA step-down (buck) regulator and a 150 mA LDO to supply all the power required for internal electronics in an connected sensor or actuator.
-
product
802.11ad Testbed, Reference Solution
Generate and analyze 802.11ad fully coded PHY waveforms for complete component, subsystem, and system performance at baseband, IF, and millimeter-wave. This Reference Solution combines Keysight Technologies software and hardware to provide a flexible testbed for 802.11ad waveform generation and analysis. Software provides the flexibility to generate and analyze 802.11ad waveforms with a wide range of different attributes. Hardware provides the flexibility to support baseband, IF, and millimeter-wave test planes. Create waveform sequences with unique 802.11ad packet structures including Modulation Coding Scheme (MCS), packet length, payload data type, and interpacket gap length, etc.
-
product
USB Power Delivery and Type-C™ Tester & Analyzer
GRL-USB-PD-C2 (GRL-C2)
GRL-USB-PD-C2 (GRL-C2) is the only solution available that supports all compliance test specifications for USB Power Delivery 3.0 and USB Type-C Alternate Mode designs, and enables product developers to quickly run full compliance and validation test suites at the push of a button. GRL-C2 provides an automated, efficient, and fully-integrated way perform all required USB Power Delivery version 3.0 and 2.0 and related tests over the USB Type-C connector, as well as PHY test automation for USB Type-C Alternate Modes. GRL-C2 automates all required USB PD compliance tests for power providers (chargers), consumers, dual-role ports, and cable and adapter E-Markers; and is the only solution available that integrates Qualcomm Quick Charge 4+ and Intel Thunderbolt-specific test items. GRL-C2 also incorporates analyzer capability to sniff PD traffic. GRL-C2 integrates all required USB PD tests into a single 2-port tester, including all tests supported on GRL’s USB-IF approved first generation solution introduced in 2015. Each port can be configured independently as a PD Provider or Consumer. All other PD Protocol and Power tests are fully integrated, removing the need for external electronic loads.
-
product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
product
MIPI M-PHY Protocol Analyzer
U4431U
Power to meet the needs of today’s and tomorrow’s designs Up to Gear 3 HS data rates Up to 16 GB trace depth Up to 4 data lanes Complete insight into complex designs Track multiple M-PHY busses from the PHY to the application layer Raw Mode 8b/10b data views Infiniium Oscilloscope integration Powerful interface that allows unlimited customization of system views
-
product
1394 and AS5643 IP Core Solutions
Synthesizable 1394 and AS5643 IP Core solutions PHY, LLLC, PHY & LLC for multiple FPGA families.
-
product
Ethernet PHY
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
product
DH series tip - CrossSync PHY PCIe5 U.2/U.3
DH-CSPHY-PCIE5-U2-U3
DH series tip - CrossSync PHY PCIe5 U.2/U.3.
-
product
Wireless Test Solutions for Bluetooth®, Wi-Fi, Matter/Thread/Zigbee
Teledyne LeCroy's Frontline family of wireless protocol analyzers, sniffers, and testers deliver unparalleled performance for complex multi-technology test environments including market-leading support for the latest Bluetooth, Wi-Fi (802.11), and Matter/Thread/Zigbee (802.15.4) technologies. We've got you covered - from RF PHY testing to protocol analysis to Bluetooth LE conformance testing.
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
IP Solution
eMMC 5.1
Demand for mobile content capacity and bandwidth for video, pictures and music is ever increasing. To address this demand in the next generation of smartphones, tablets, and portable devices, the eMMC 5.1 Specification from JEDEC, improves the current HS400 speeds operating at 3.2Gbps, with "command queuing" making the data transfers highly efficient by offloading the software overhead into the controller. eMMC 5.1 further improves the reliability of operation by utilizing an "enhanced strobe" at the PHY layer. The eMMC5.1 is backward compatible with the existing eMMC 4.51 and eMMC 5.0 Devices.
-
product
Training Board
JT 2156
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
product
System on Module Microsemi PolarFire
SoM3-MPF300T
Sundance Multiprocessor Technology Ltd.
The SoM3-MPF300T is a small footprint System On Module (SoM) with 40x50mm dimensions. It has a low power, highly secure FPGA from the PolarFire family from Microsemi. It comes with 4GB of DDR4 memory, Ethernet PHY, and FLASH. This SoM is ideal for being used in complex hardware designs, and is compatible with Sundance SoM carriers SE215 and EMC2-DP-V2.
-
product
Digital Services
*Processor verification experience*Memory verification*Bus protocols and DMA verification*Expert in high speed controller verification*Physical layer (PHY) verification
-
product
Digital Optical Transport
The ATX GigaWave digital optical transport portfolio is designed to fortify cable operators with maximum flexibility and cost efficiencies to support a range of applications and business models. The GigaWave Digital Link Extender (DLX) is optimized to support distributed access architectures (DAA), including Remote PHY (R-PHY) and Remote MACPHY (R-MACPHY), as well as Passive Optical Network (PON), Small Cell/5G and enterprise business services. The GigaWave Digital Link Amplifier-HUB (DLA-HUB) is a field-hardened, gain-flattened EDFA platform that enables the elimination of physical hub sites along long-reach optical routes. The GigaWave digital optical transport portfolio also enables MSOs to leverage the advantages of digital optics over analog, including the capability to transport signals over longer distances and provision additional wavelengths per fiber.
