Filter Results By:
Products
Applications
Manufacturers
Comb Generators
a reference signal source outputing multiple harmonics of the input signal.
See Also: Open Area Test Sites
- Applied Instruments, Inc.
product
CATV Multi Carrier Signal Generators
5112
The 5112 is a portable RF signal generator, available in four or six carrier configurations. Each carrier can be activated individually or simultaneously.
-
product
Comb Generator, 10 MHz To 110 GHz
U9391M
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator
CG 50/500
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN. reference signal source Noise Generators Signal Generators
-
product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
Low Phase Noise Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
product
RefRad Comb Generators
RadRad is a battery-operated comb generator as well as a field source. It is a valuable tool for engineers ensuring the quality of radiated and conducted EMC and EMF measurements.
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Reference Radiators / Comb Generators
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
product
Comb Generators
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
product
Comb Generators
Macom Technology Solutions Holdings Inc.
MACOM offers a family of Non-Linear-Transmission-Line (NLTL) GaAs Comb Generators offering superior phase noise performance up to -18 dBc/Hz better then a SRD, usable harmonics out to 50 GHz, and available in SMT or connectorized packages. Standard drive levels from 18 - 21 dBm.
-
product
Comb Generator, 10 MHz to 67 GHz
U9391G
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator
CG01
The main application of Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble shooting Open Area Test Sites(OATS).An OATS must be completely calibrated before it is put into service. reference signal source Noise Generators Signal Generators
-
product
Comb Generator
CG118
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
product
Radiating Comb Generators
TBCG1
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
product
Comb Generator
RefRad X
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
product
Generators
Saw-Tooth Signal Generator
The Software Signal generator allows to produce triangular and saw-tooth (descending, ascending) signals at the DAC output.
-
product
Comb Generator
WJ10-25A
Comb Generator model WJ10-25A with Broadband Antenna. Frequency Range 10 MHz - 8 GHz, with two frequencies step size option; 10/25 MHz
-
product
Generators
Noise Generator
The noise type to be generated is to be selected from the context menu: right-click the section with the noise name and select the noise type you need.
-
product
Plastic Wet Film Combs
154
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
product
USB Harmonic Comb Injector
J2150A
The USB Harmonic Comb Injector is a fast, easy-to-use, ultra-portable signal generator for interrogating your PDN to identify noise sensitivities. Quickly identify power supply related issues. Multiple modes include time and frequency jitter. Wideband harmonic comb spans 1kHz-1GHz+. Great for clock power supply EMI spectrum testing.
-
product
Comb Generator
WJ10-100A
Comb Generator model WJ10-100A with Broadband Antenna. Frequency Range 10MHz - 11 GHz with two frequencies step size option; 10/100 MHz
-
product
Signal Generators
Are capable of producing accurate sine, square, triangle, pulse, and arbitrary waveforms.
-
product
Generators
Pulse Signal Generator
The Software Signal generator allows to produce pulse signals with various pulse ratio and frequency at the DAC output.
-
product
Signal Generators
NF‘s function generators have been used in many applications, since NF produced the first Japan-built function generator in 1959.A function generator is general-purpose test equipment used to generate various waveforms and to execute trigger, sweep and gate oscillation.
-
product
Generators
Signal Generator
Signal Generator is used for forming signals of various shapes, amplitude, and frequency at the output channels of ADC and DAC modules and FFT spectrum analyzers. Functionally, the Signal Generator software replaces stationary generators used in laboratories.
-
product
Logo Generators
Overlays bit-mapped (BMP) graphics on analog or digital videoAdjustable in brightness and transparencySmooth up/down transitionsNTSC and PALLG-1 Plus and LG-4: Composite video or optional Y/CHDLG: Digital video with automatic detection of input standard and format
-
product
Signal Generators
ZTX-Series
RPG's Signal Generator Extenders allow high performance frequency extension of microwave sources into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. These modules combine high test-port power with low phase noise to offer exceptional performance. Contact RPG to discuss Signal Generator Extenders configurations that will gain the best performance for your application.
-
product
Impulse Generators
Provides pulse widths (measured at the 20% rise timepoint) in the range of 130 ps to 2 ns, amplitudes as high as 100 Volts, with pulse repetition frequencies to 1 MHz.
-
product
Generators and Sources
For general purpose standalone applications or as core components in a high speed test and measurement system, Yokogawa sources and signal generators are highly accurate and functional. The integration of source and measurement into a single unit greatly simplifies the test process. Semiconductor devices, sensors, displays or batteries etc can therefore be quickly and easily characterized.
-
product
Signal Generators
Kuhne electronic Signal Generators are available in the following variations:RF Generator as Compact Module in the form factor of a power amplifier (frequency and power can be adjusted)Laboratory Instrument for immediate use with self-explaining user interface for adjustment of frequency and power as well as multiple monitor information possibilities
