Filter Results By:
Products
Applications
Manufacturers
-
product
Variable Optical Attenuator Module for Multimode Fiber Applications
81578A
The Keysight 81578A variable optical attenuator is designed for multimode fiber applications and features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
2 Channel Variable Optical Attenuator
S-105
VOA slot module of FOTS system is a module that installs a built-in dual channel MEMS type VOA inside and can do two separate attenuation functions with two each VOA channel being driven individually. This module controls the optical power precisely to maintain the desired output level set by the user by automatically correcting for power drift or fluctuation.This slot module provides high-performance power control features such as high attenuation range, accurate tolerance, stable spectral flatness and low insertion loss in the wavelength range of 1260 ~ 1600 nm. It also offers a particularity that the high-speed drive of attenuation is possible through the combination of high-speed FPGA processor and high speed response time (within 1 ms) VOA. With the provided driving program and GUI, users can set up various attenuation program of each VOA channel such as sequential attenuation step, periodic attenuation and operation time
-
product
RFoG 4-Band Multiplexer. 1550, 1590 & 1310/1490nm MWDM
WD5943
Hangzhou Huatai Optic Tech. Co., Ltd.
WD5943 WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to FTTx PON network to achieve the combination and separation of the 1550nm (CATV) and 1310/1490nm (data).
-
product
Probe Card PCB's
DTS offers both generic and custom PCBs blanks for probe cards. Probe card PCBs are available for all tester platforms and can be configured for any vertical technology, epoxy cantilever and legacy blade cards. DTS probe card blanks are made to precise specifications required for all probing technologies and are available in high speed and high temperature materials. All probe card PCBs employ a balanced layering construction to maintain tight flatness specifications and minimize warping, allowing good probe planarity. Gold plating on all surface metals facilitates easy soldering and minimizes probe resistance. DTS is continually adding new probe card blanks to its library!
-
product
Satellite Optical Receiver
SSR-15CW
Hangzhou Softel Optic Co., Ltd.
*Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using high linear PD*Output connected to 5 IN series satellite multiswitch*Build-in optical AGC function*Red-LED for power indication*Smaller size and easier installation
-
product
Optics Test Equipment + Flatness, Bow, Warp, Curvature, Glass Thickness
Wedge Angle Scanner For Car Windshields
Optik Elektronik Gerätetechnik GmbH
Scanning of complete car windshields for measurement of wedge angle and thickness distribution, in particular in the HUD area.
-
product
Flatness, Bow, Warp, Curvature, Glass Thickness
1D-glass Thickness Profile Measuring Instrument GPM2
Optik Elektronik Gerätetechnik GmbH
Highly accurate automatic measurement of glass thickness distributions. The glass thickness profiler GPM has the function to execute a fast and precise determination of the thickness profile of flat glass samples or another transparent material with a thickness range from 30µm to 700µm (option with sensor type 1) and width to 1200mm. The measuring point distance of the profile measurement can be varied over a micro-step-controlled positioning steering between 0.1mm and 1mm. The measured value accommodation for a scanning point takes place with the help of a special hardware module for image processing algorithms within 40 ms. The entire measuring time for a sample results thus as product from the sample width which has to be measured, the measuring point distance and the measuring time per measuring point.
-
product
RF Power Amplifiers
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
-
product
Flatness, Bow, Warp, Curvature, Glass Thickness
FLATSCAN 650 3D
Optik Elektronik Gerätetechnik GmbH
High accurate flatness & thickness measuring system for large substrates.
-
product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
ELCOLEVEL - Software For 3D-straightness Measurement
Optik Elektronik Gerätetechnik GmbH
ELCOLEVEL is a software with interfaces to electronic autocollimators and inclination levels of different manufactureres. This allows for example the 3D-Straightness measurement (twist-, roll- and yaw-angle) of slides in one and the same measuring procedure.
-
product
900 MHz Trunk Hybrid Amplifier
AS 1515
Hybrid Amplifiers used in Trunk and branch lines specially designed to serve the needs of cable systems with very Long Trunk Cables. They are in Aluminium Housing providing maximum heat dissipation and have RFI Shielding. They incorporate superior quality Hybrid IC Module to obtain excellent features.- Frequency Range: 40 ~ 1000 MHz- Mains cum Power Pass- Output Level: 102 dBµV- Level Flatness: ±0.75 dB- 32 dB Gain (40 dB Optional)- Optimum for- Trunk Distribution- Superior Quality- Hybrid IC Module- Hybrid IC Protected- Voltage Selection LED - for Easy Selection
-
product
Microwave Wideband PIN-TIA Receivers
MR22 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR22 series microwave wideband optical receiver, adopts High linear PIN diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
32 to 40GHz, 10W GaAs Hybrid SSPA Module
AMP3060
Exodus Advanced Communications
Best in Class SSPA model AMP3060 - a 32 to 40GHz, 10W GaAs Hybrid SSPA Module. It provides 10W CW Psat over the full band with 4.0dB Peak to Peak flatness. Additional features include high reliability and ruggedness along with suitability for all single channel modulation standards. This amplifier is designed for any application that requires wide band coverage such as EMI/RFI, KA band Radar, EW and High Power Millimeter Testing.
-
product
Optical Transmitter
ST1015-10mW
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home) Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices*Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
product
Preamplifier, 100 MHz to 18 GHz
87405C
Exceptional gain (25 dB) and flatness (1.5 dB) combined with a probe-power bias connection which eliminates the need for an additional DC power supply, makes these preamplifiers the ideal choice for spectrum analyzer or stand alone applications.
-
product
Optical Transmitter
ST1013-3mW
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home)Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices *Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
product
Fiber End-Face Inspection Interferometer
CLEAVEMETER 3D
The CLEAVEMETER 3D™ is a non-contact interferometer designed for inspecting the end-faces of cleaved or polished optical fibers with cladding diameters of 125 µm to 1200 µm. It gives immediate and precise information on important end-face properties such as flatness, perpendicularity, hackles and dust. Based on the NYFORS CLEAVEMETER 3D™ design, in addition to producing sharp fringe patterns it also generates three-dimensional images of the cleaved fiber end.
-
product
Capacitance Sensor Systems
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
product
Attenuators
The 01311 attenuator chip series is designed to achieve precision and tight flatness with an attenuation accuracy of ± 0.2 dB on our 1-10 dB pads and ± 0.3 dB on our 11-20 dB pads. SemiGen tests 100% of all attenuator chips prior to shipment to verify that they meet specifications.
-
product
(125×150×20mm) C-Band DWDM Line EDFA Module
WLA4200-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WLA4200-FM05 series is a gain flatness line EDFA Module which is specifically designed for C-Band 44 channels optic transmission system. It adopts the most excellent optical performance, the most advanced electronic control technology and the most complete software functionalities; it is featured with wide working wavelength range, low noise and excellent gain flatness. WLA4200-FM05 is mainly installed in middle of transmission line, replacing the traditional relay, to compensate the optical power loss in the line and extend the optical signal transmission distance
-
product
Low Noise Super Wide Band Amplifiers
WBA Series
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
product
Medium-Power, Broadband Amplifiers
Our family of distributed amplifiers utilize advanced broadband design techniques to achieve solid performance in gain, flatness, noise figure and output power over a wide frequency range. The experienced design team has the know-how and tools available to take any standard product and customize it for your specific application.
-
product
(70×90×15mm) C-Band DWDM Full Function Pre EDFA Module
WPA4300-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Huatai WPA4300-FM02 series with 70 × 90 × 15mm MSA compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 waves DWDM system applications.
-
product
SDC-C Series Microwave Downconverter
SDC-C
SDC-C Series Microwave downconverter is a broadband frequency converter that is dedicated for satellite communication. It has a high performance, high reliability and an octave covered by RF signal. Its frequency step is precise and accurate to 1Hz with a variety of IF and signal bandwidth choices. SDC-C series is equipped with functions like self-testing and combination alarm which is suitable for long-time uninterrupted use, guaranteed safety and reliability.SDC-C series microwave downconverter is mainly designed for satellite communication system, signal monitoring system, and electronic countermeasure system with an excellent phase noise, clutter suppression, and in-band flatness data. It is able to provide a transparent RF transmission channel to all videos or data communications. All programming commands can be set through a local panel or through network remotely. SDC-C series microwave downconverter has a standard 2U size.Applications: T&M Systems / Satellite Communications / MIMO
-
product
High Isolation 1310/1550nm WDM
HWD1315
Hangzhou Huatai Optic Tech. Co., Ltd.
HWD1315 high isolation WDM is based on mature thin film filtering tech, metal sealing technology package. HWD1315 is used in combination and separation of 1310nm and 1550nm band optical signal. Its wide bandwidth, flatness, low insertion loss and isolation are higher than the average MWDM devices and so on.
-
product
Microwave Wideband APD-TIA Receivers
MR12 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR12 series microwave wideband optical receiver, adopts high Sensitivity APD diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
product
Noise Generator
UFX7000
The UFX7000A Series instruments provide Broadband Gaussian noise with superior flatness. The output power can be attenuated up to 127 dB in 1 dB steps, and several connector types are available.
-
product
Interferometer
VFI-2000
The VFI is the interferometer of choice for industry leading photonics companies around the world. The VFI-2000 is an interferometric inspection system specifically designed for checking the surface quality and flatness of your cleaved or polished fibers. The VFI offers the perfect combination of a superb image quality with ease of use, and the reliability and robustness that our customers have come to expect from Arden products, resulting in fiber end face measurements that you can trust.
-
product
Comb Generator/Frequency Multiplier
TBCG2
The TBCG2 is a passive, step recovery diode based comb generator/frequency multiplier. It is optimized for moderate drive power and spectrum flatness in the frequency range 1 MHz to 2.5GHz.
