Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Pneumatic Contact, ITA, Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131106
Primary mating contact 610131107.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
product
Fuel Pressure Testers
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
product
Pneumatic Contact, ITA, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610132101
Primary mating contact 610131101.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferruless fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
product
Abrasion Testers
Abrasion tester is used to determines the resistance of elastomers by the frictional loss of the rubber in products, such as tires, conveyor belts, hoses, footwear, floor covering etc.
-
product
Peristaltic Pumps
PeriXus
Teledyne LABS PeriXus® peristaltic pumps was developed with your lab or manufacturing plant in mind. With its compact and modular design, this space-saving pump uses peristaltic technology to help reduce the possibility of contamination, making it a great pump to use when handling volatile materials.The ability to quickly change hoses allows you to switch from pumping one material to another in minutes, maximizing application flexibility. The available hose options are designed to handle even the toughest materials, including highly viscous fluids. With a flow rate of 0.005 to 162 mL/min, this peristaltic pump is ideal for a variety of markets, including pharmaceutical/biotechnology, research and development, petrochemical, and reaction chemistry.
-
product
Hydraulic Hose Assemblies, 15,000 psi, USAF, US Army
8801B Tester
This hydraulic hose tester is manufactured to, and meets all the requirements of, military specification MIL-T-25456B and federal specification A-A-52687. Enhanced safety for operating personnel is achieved by utilizing the optional 8801HT integral test chamber which was designed specifically to fit to all our 8801B and 9801B testers.
-
product
Needle Pressure Gauge
102
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
product
Air Hose Reel Tool Balancers
The air hose tool balancer is designed for small pneumatic tools. Integrating the air hose and support cable together keeps the work area clean. These durable tool balancers provide easy handling for operators that work with tools for long, continuous hours. The tool balancer allows a tool to be positioned over the work station for comfortable operation and can be used with a pneumatic screwdrivers or other small air tools. Protects an assembly tool from accidentally damage, like being knocked off a workbench. The effortless handling of the balancer provides comfortable tool operation and increased production.
-
product
Build Your Hydrostatic Tester
Start with the basic Model 9901 hydrostatic tester as shown to the left with the following standard equipment:- Hydrostatic test pump, air operated.- 1% ANSI B40.1 Grade 1A stainless steel high pressure gauge.- ANSI B40.1 Grade B air pressure gauge.- Micro adjust precision regulator.- High pressure isolation shutoff valve.- Automatic lubricator.- Stainless steel high pressure manifold.- 1/4" NPT accessory port.- Bleed valve.- Air shutoff valve.- Factory set air pressure relief valve.- 7/16-20 straight thread O-ring boss outlet port (MS33649-04) with -4 male adapter fitting.- 3/4" swivel female hose inlet with strainer.- Stainless steel base plate with rubber feet.
-
product
Ralston Quick-test™ Connection System
Save time and frustration with Quick-test, the versatile system of quick connect high-pressure hoses and universal hose connectors that connect to anything.
-
product
Automatic Transmission & Engine Oil Pressure Tester
34500
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Gage calibrated from 0-600 PSI (0-4,000 kPa & 0-7.0 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a durable vinyl pouch.
-
product
Hose Continuity Tester
OhmGuard
The OhmGuard hose continuity tester is designed to test hoses used on vacuum trucks and tanker trucks prior to the transfer of flammable or combustible products
-
product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-36x36x15
The 3 ft. wide x 3 ft. deep Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
product
Hybrid / Optical Dry Mate Connector
The Teledyne ODI Dry-Mate Submersible connector series is designed to directly complement the wet-mate hybrid connector series (Rolling Seal), and also for use as a stand-alone connection system. Two standard shell sizes are available, depending on the circuit configuration. In addition, straight, 45°, or 90° termination versions can be provided. Used in conjunction with Teledyne ODI's oil-filled hose, this system is designed for submersible applications up to 9,100 psi. A unique tri-lobe keying system assures proper alignment.
-
product
MASTER FUEL PRESSURE TEST KIT
FIT550
*Performs running, residual, rail and flow rate pressure tests*Large, easy-to-read 3-1/2" dual-scale gauge reads 0-100psi and 0-700 kPa*Kit includes: 50+ adapters, fittings, 48" hose, pressure relief and fuel discharge hose to test most domestic and foreign fuel injection systems*Also includes quick release couplers and adapters to fit other fuel injection test kits*For use with gas engines only
-
product
Energized Cable Sensor
The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.
-
product
Ralston Quick-test™ Microbore Calibration Hoses
Ralston Instruments Quick-test™ hoses can be attached and detached without a wrench or thread sealant while maintaining a working pressure of 6900 psi (475 bar). Quick-test hoses are small in diameter, flexible, and low in volume. These hoses provide an ideal way of transmitting pressure during a vacuum or pressure calibration. A wide variety of adaptors provide a connection for most calibration applications.
-
product
Hydrostatic Test Pump, 6300 psi, P/N 9501C - USAF
9501C
The 9501-9501C hydrostatic test pump provides a safe source of hydraulic pressure for proof testing pressure vessels, hose and tube assemblies or other components that require periodic proof pressure testing.
-
product
DIESEL COMPRESSION ADAPTER FOR FORD AND INTERNATIONAL
DTC1524
*M14 x 1.25 thread adapter attached to hose and a quick disconnect*Screws into the head of the engine in the glow plug hole*Use on International VT 365 engine used in the International 4200 medium-duty truck and Ford Powerstroke 6.0L used in the Ford F250-F550 trucks
-
product
Line Switching Unit Series
TestVonics™ Line Switching Unit (LSU) is a multi-port distribution unit which can provide up to 6 outputs from one channel of controlled pressure. The LSU distributes pitot static supplies for the external services and connection of hose assemblies for testing of aircraft Pitot and Static ports. The lightweight unit is housed in a highly durable and easy to maneuver case.
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
Hydrostatic Testers
Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 30 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07. In addition to U.S. Military stock listed hydrostatic testers, we manufacture both standard and custom hose proof test stands, portable hydrostatic testers, hydrostatic test chambers and ancillary equipment to fit individual customers’ needs as required. We can typically ship standard units within 24-72 hours, sooner if required.
-
product
Diesel Dynamometers
Heavy-duty toroidal water-brake or large eddy-current absorber, S-beam electronic torque transducer, high-flow manual (or optional electronic) engine load control, DYNOmite data-acquisition computer, rigid-frame engine test stand, wall (or stand) mounted control console, absorber to engine-block mounting adapter, heavy-duty input shaft, calibration arm, stainless-braided hoses, and full-function data wiring harness.
-
product
Small Engine Dynamometers
Toroidal-flow water-brake absorber (with 5" high-RPM rotor), electronic torque-arm transducer, engine load control, DYNOmite handheld data-acquisition computer, AC power supply, stainless-braided hoses, magnetic RPM sensor, data wiring harness, and protective carrying case.
-
product
thermostats
Cooling bath circulation thermostats - freezing test set of equipment 2 pieces for carrying out the freezing test with 42-2260 .... Complete with insulated connection hoses and connection elements as well as integrated circulating pumps for temperature control of a single or double sample. The temperature setting is software-controlled. For connection, 2 separate fused circuits per 16 A are required.
-
product
Pitot Static Tester
ADSE 643
The ADSE 643 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fixed and rotary wing.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The ease of use and portability enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.The test set is housed in an anodized metal and rugged case.An attached case contains the pressure hoses and electrical cables.
-
product
Safety Chamber, Hydrostatic Test
9901HTX-36x36x15
The 3 ft wide by 3 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
product
Portable Hydrostatic Hose Tester, 15000 psi; USMC
9901HT-8762
The 9901HT-8762 Hydraulic Hose Test System is utilized by the United States Marine Corp. for their portable forward base maintenance stations. The system includes it's own onboard "quiet" air compressor and a set of 37 degree flared test adapters from 3/16" through 2" as well as an onboard calibration gauge and pneumatic castors for use on rough terrain.
-
product
AIS Air Data Test System
F-16
The primary function of the Air Data Test System (ADTS) is to perform testing and fault isolation of pneumatic-type Units Under Test (UUTs). To test a UUT, the operator connects the associated Line Replaceable Unit (LRU) Integrated Test Adapter (ITA) to the rackmount Avionics Intermediate Shop (AIS) test station. The operator connects the ADTS to the IAIS via an RS-232 Interface and then finally, connects the UUT to the ADTS using the supplied cables and hoses.
-
product
Radiator Flow Test Machine
8601
The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection to different size radiators. The complete unit is mounted on swiveling casters. The flow rate is infinitely adjustable from 0 to 120 gallons per minute by means of a panel mounted control valve. The machine is constructed from heavy 10 gauge steel, is double welded and is coated externally and internally with a water-resistant epoxy coating. Flow measurement is accomplished by a digital panel meter with a calibrated accuracy of plus or minus 3 percent of scale between 5 and 120 gallons per minute. Higher flows available on request.
