Test Electronics
Manufacturers of Electronic Test Equipment, Bed of Nails Test Fixtures, Solder Pallets, and Production Assembly Fixtures
- 831 763 2000
- 909.498.8709
- 821 Smith Road
Watsonville, CA 95076
United States
-
product
Hi Potential & Cable Continuity Test Fixture
HIPOTCCT
The most important features of this hipot tester fixture is its safety and ease of use intuitive control functions and durability in a production environment.
-
product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
Test Probes and Pins
Spring Loaded Test Probes for Circuit Board Testing, "Pogo Pins" Test Electronics sources and stockes a large variety of Test Probes and Spring Loaded Test Pins. Let our applications engineers help you find the correct pin for your test fixture application.
-
product
High Voltage Surge Testers
HVST
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
product
Process Carrier Pallets
Metalic Family
Process carrier pallets to carry the circuit boards through pick-n-place, IR reflow, gold wire bonding, epoxy dot encapsulating, and final fuctional test. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets. Process carrier pallets can be designed to carry your circuit boards through assembly, wash and final test.
-
product
Ceramic Process Carrier Pallets
Ceramic engineering specializing in Silicon Carbide, Boron Carbide, Alumina, Zirconia and Lead Zirconate Titanate (PZT) based ceramics, composites and thin films for High Strength, high temperature, semiconductive ceramic designed for use in wafer fabrication or hybrid circuits in vapor deposite ovens. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets.
-
product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Telephone Headset and Handset Test System
THT
TE2000 Headset Tester for audio testing headsets and handsets using computer generated test sounds.
-
product
High Carbon Process Carrier Pallets
Composite Family
High Strength, high temperature, semiconductive composite board designed for use as circuit board and flex circuit carrying pallets for solder reflow ovens.
-
product
Regulated Variable 0-300VAC Power Supply
300VAC
The most important features of the power supply is its ability to hold a constant voltage as the power lines fluxuate and the load fluctuates. Used for testing testing high and low line conditions for any AC powered device.
-
product
GPIB Controlled Signal Routing Box
GPIB
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
product
Edge Press Technology Bed of Nails Testers
Rand Edge Press Family
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
product
Edge Press Technology Bed of Nails Testers
Prober Edge Press Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
product
Edge Press Technology Bed of Nails Testers
Protector Edge Press Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
